参数资料
型号: EVAL-ADUC7124QSPZ
厂商: Analog Devices Inc
文件页数: 93/108页
文件大小: 0K
描述: BOARD EVALUATION FOR ADUC7124
设计资源: EVAL-ADUC7124 Schematic
ADUC7124 Eval Brd Gerber Files
标准包装: 1
系列: MicroConverter® ADuC7xxx
类型: MCU
适用于相关产品: ADUC7124
所含物品:
Data Sheet
ADuC7124/ADuC7126
Rev. C | Page 85 of 108
IRQEN Register
IRQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled to
create an IRQ exception. When a bit is set to 0, the correspond-
ing source request is disabled or masked, which does not create
an IRQ exception. The IRQEN register cannot be used to
disable an interrupt.
IRQEN Register
Name:
IRQEN
Address:
0xFFFF0008
Default Value:
0x00000000
Access:
Read/write
IRQCLR Register
IRQCLR is a write-only register that allows the IRQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the IRQEN register without
affecting the remaining bits. The pair of registers, IRQEN and
IRQCLR, allow independent manipulation of the enable mask
without requiring an atomic read-modify-write.
This register should be used to disable an interrupt source only
during the following conditions:
In the interrupt sources interrupt service routine.
When the peripheral is temporarily disabled by its own
control register.
This register should not be used to disable an IRQ source if that
IRQ source has an interrupt pending or may have an interrupt
pending.
IRQCLR Register
Name:
IRQCLR
Address:
0xFFFF000C
Default Value:
0x00000000
Access:
Write only
FAST INTERRUPT REQUEST (FIQ)
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface and provides the
second level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Bit 31 to Bit 1 of FIQSTA are logically OR’ed to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and FIQCLR does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN clears, as a side effect, the same bit in IRQEN.
Likewise, a bit set to 1 in IRQEN clears, as a side effect, the
same bit in FIQEN. An interrupt source can be disabled in both
the IRQEN and FIQEN masks.
FIQSIG
FIQSIG reflects the status of the different FIQ sources. If a
peripheral generates an FIQ signal, the corresponding bit in
the FIQSIG is set; otherwise, it is cleared. The FIQSIG bits are
cleared when the interrupt in the particular peripheral is
cleared. All FIQ sources can be masked in the FIQEN MMR.
FIQSIG is read only.
FIQSIG Register
Name:
FIQSIG
Address:
0xFFFF0104
Default Value:
0x00000000
Access:
Read only
FIQEN
FIQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled to
create an FIQ exception. When a bit is set to 0, the correspond-
ing source request is disabled or masked, which does not create
an FIQ exception. The FIQEN register cannot be used to disable an
interrupt.
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default Value:
0x00000000
Access:
Read/write
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
This register should be used to disable an interrupt source only
during the following conditions:
In the interrupt sources interrupt service routine.
The peripheral is temporarily disabled by its own control
register.
This register should not be used to disable an IRQ source if that
IRQ source has an interrupt pending or may have an interrupt
pending.
相关PDF资料
PDF描述
ECM30DCWN CONN EDGECARD 60POS DIP .156 SLD
EVAL-ADUC7121QSPZ BOARD EVALUATION FOR ADUC7121
EVAL-ADUC7126QSPZ BOARD EVALUATION FOR ADUC7126
REC5-243.3SRWZ/H4/A CONV DC/DC 5W 9-36VIN 3.3VOUT
EVAL-ADUC7023QSPZ KIT DEV FOR ADUC7023 QUICK START
相关代理商/技术参数
参数描述
EVAL-ADUC7126QSPZ 功能描述:BOARD EVALUATION FOR ADUC7126 RoHS:是 类别:编程器,开发系统 >> 通用嵌入式开发板和套件(MCU、DSP、FPGA、CPLD等) 系列:MicroConverter® ADuC7xxx 标准包装:1 系列:PICDEM™ 类型:MCU 适用于相关产品:PIC10F206,PIC16F690,PIC16F819 所含物品:板,线缆,元件,CD,PICkit 编程器 产品目录页面:659 (CN2011-ZH PDF)
EVAL-ADUC7128QSPZ 功能描述:KIT DEV FOR ADUC7128 RoHS:是 类别:编程器,开发系统 >> 通用嵌入式开发板和套件(MCU、DSP、FPGA、CPLD等) 系列:QuickStart™ PLUS 套件 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板,软件,4x4 键盘,光学拨轮,QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA
EVAL-ADUC7128QSPZ2 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC
EVAL-ADUC7129QSPZ 制造商:Analog Devices 功能描述:- Bulk
EVAL-ADUC812QS 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM