- 您现在的位置：买卖IC网 > PDF目录17109 > EVAL-ADUC7023QSPZ (Analog Devices Inc)KIT DEV FOR ADUC7023 QUICK START PDF资料下载
参数资料
| 型号： | EVAL-ADUC7023QSPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 75/96页 |
| 文件大小： | 0K |
| 描述： | KIT DEV FOR ADUC7023 QUICK START |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | ARM7TDMI |
| 所含物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页当前第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
Data Sheet
ADuC7023
| Page 77 of 96
IRQEN Register
Name:
IRQEN
Address:
0xFFFF0008
Default value:
0x00000000
Access:
Read/write
Function:
IRQEN provides the value of the current
enable mask. When each bit is set to 1, the
source request is enabled to create an IRQ
exception. When each bit is set to 0, the
source request is disabled or masked, which
does not create an IRQ exception.
To clear an already enabled interrupt source,
users must set the appropriate bit in the
IRQCLR register. Clearing an interrupt
IRQEN bit does not disable this interrupt.
IRQCLR Register
Name:
IRQCLR
Address:
0xFFFF000C
Default value:
0x00000000
Access:
Write
Function:
IRQCLR (write-only register) clears the
IRQEN register to mask an interrupt source.
Each bit set to 1 clears the corresponding bit
in the IRQEN register without affecting the
remaining bits. The pair of registers, IRQEN
and IRQCLR, independently manipulate the
enable mask without requiring an atomic
read-modify-write.
FAST INTERRUPT REQUEST (FIQ)
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface and provides the
second level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Bit 31 to Bit 1 of FIQSTA are logically OR’ed to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and FIQCLR does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN clears, as a side effect, the same bit in IRQEN. Likewise,
a bit set to 1 in IRQEN clears, as a side effect, the same bit in
FIQEN. An interrupt source can be disabled in both IRQEN
and FIQEN masks.
FIQSIG
FIQSIG reflects the status of the different FIQ sources. If a
peripheral generates an FIQ signal the corresponding bit in
the FIQSIG is set, otherwise it is cleared. The FIQSIG bits are
cleared when the interrupt in the particular peripheral is cleared.
All FIQ sources can be masked in the FIQEN MMR. FIQSIG is
read only.
FIQSIG Register
Name:
FIQSIG
Address:
0xFFFF0104
Default value: 0x00000000
Access:
Read only
FIQEN
FIQEN provides the value of the current enable mask. When a bit is
set to 1, the corresponding source request is enabled to create an
FIQ exception. When a bit is set to 0, the corresponding source
request is disabled or masked which does not create an FIQ
exception. The FIQEN register cannot be used to disable an
interrupt.
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default value: 0x00000000
Access:
Read/write
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear in order to mask an interrupt source. Each bit that is set
to 1 clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
This register should only be used to disable an interrupt source
when in the interrupt sources interrupt service routine or if the
peripheral is temporarily disabled by its own control register.
This register should not be used to disable an IRQ source if that
IRQ source has an interrupt pending or could have an interrupt
pending.
FIQCLR Register
Name:
FIQCLR
Address:
0xFFFF010C
Default value:
0x00000000
Access:
Write only
Rev. E
相关PDF资料 |
PDF描述 |
|---|---|
| RPS-1K-6-250/2.0-9 | HEAT SHRINK SLEEVE |
| ECM30DCWH | CONN EDGECARD 60POS DIP .156 SLD |
| SC43B-3R3 | INDUCTOR SMD 3.3UH 1.44A 7.96MHZ |
| EVAL-ADUC842QSPZ | KIT DEV QUICK START ADUC842 |
| EVAL-ADUC841QSPZ | KIT DEV QUICK START ADUC841 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADUC7023QSPZ1 | 功能描述:BOARD EVAL FOR ADUC7023 RoHS:是 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADuC7023QSPZ2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU with Enhanced IRQ Handler |
| EVALADUC7023QSPZU1 | 制造商:Analog Devices 功能描述: |
| EVAL-ADUC7024QS | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk |
| EVAL-ADUC7024QS-U2 | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。