- 您现在的位置：买卖IC网 > PDF目录17109 > EVAL-ADUC7023QSPZ (Analog Devices Inc)KIT DEV FOR ADUC7023 QUICK START PDF资料下载
参数资料
| 型号： | EVAL-ADUC7023QSPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/96页 |
| 文件大小： | 0K |
| 描述： | KIT DEV FOR ADUC7023 QUICK START |
| 标准包装： | 1 |
| 类型： | MCU |
| 适用于相关产品： | ARM7TDMI |
| 所含物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
ADuC7023
Data Sheet
| Page 38 of 96
SECURITY
The 62 kB of Flash/EE memory available to the user can be read
and write protected.
Bit 31 of the FEEPRO/FEEHIDE MMR (see Table 34) protects
the 62 kB from being read through JTAG programming mode.
The other 31 bits of this register protect writing to the flash
memory. Each bit protects four pages, that is, 2 kB. Write
protection is activated for all types of access.
Three Levels of Protection
Protection can be set and removed by writing directly into
FEEHIDE MMR. This protection does not remain after reset.
Protection can be set by writing into FEEPRO MMR. It only
takes effect after a save protection command (0x0C) and a reset.
The FEEPRO MMR is protected by a key to avoid direct access.
The key is saved once and must be entered again to modify
FEEPRO. A mass erase sets the key back to 0xFFFF but also
erases all the user code.
Flash can be permanently protected by using the FEEPRO
MMR and a particular value of key: 0xDEADDEAD. Entering
the key again to modify the FEEPRO register is not allowed.
Sequence to Write the Key
1. Write the bit in FEEPRO corresponding to the page to be
protected.
2. Enable key protection by setting Bit 6 of FEEMOD (Bit 5
must equal 0).
3. Write a 32-bit key in FEEADR, FEEDAT.
4. Run the write key command 0x0C in FEECON; wait for
the read to be successful by monitoring FEESTA.
5. Reset the part.
To remove or modify the protection, the same sequence is used
with a modified value of FEEPRO. If the key chosen is the value
0xDEAD, the memory protection cannot be removed. Only a mass
erase unprotects the part, but it also erases all user code.
The sequence to write the key is illustrated in the following
example (this protects writing Page 4 to Page 7 of the Flash):
FEEPRO=0xFFFFFFFD;
//Protect Page 4 to
Page 7
FEEMOD=0x48;
//Write key enable
FEEADR=0x1234;
//16 bit key value
FEEDAT=0x5678;
//16 bit key value
FEECON= 0x0C;
//Write key command
The same sequence should be followed to
protect the part permanently with
FEEADR =
0xDEAD and FEEDAT = 0xDEAD.
FLASH/EE CONTROL INTERFACE
Serial and JTAG programming use the Flash/EE control interface,
which includes the eight MMRs outlined in this section.
FEESTA Register
Name:
FEESTA
Address:
0xFFFFF800
Default value: 0x20
Access:
Read
Function:
FEESTA is a read-only register that reflects the
status of the flash control interface as
described in Table 31.
Table 31. FEESTA MMR Bit Designations
Bit
Description
7 to 6
Reserved.
5
Reserved.
4
Reserved.
3
Flash interrupt status bit.
This bit is set automatically when an interrupt occurs, that is, when a command is complete and the Flash/EE interrupt enable bit
in the FEEMOD register is set.
This bit is cleared when reading FEESTA register.
2
Flash/EE controller busy.
This bit is set automatically when the controller is busy.
This bit is cleared automatically when the controller is not busy.
1
Command fail.
This bit is set automatically when a command is not completed.
This bit is cleared automatically when reading FEESTA register.
0
Command pass.
This bit is set by the MicroConverter when a command is completed.
This bit is cleared automatically when reading the FEESTA register.
Rev. E
相关PDF资料 |
PDF描述 |
|---|---|
| RPS-1K-6-250/2.0-9 | HEAT SHRINK SLEEVE |
| ECM30DCWH | CONN EDGECARD 60POS DIP .156 SLD |
| SC43B-3R3 | INDUCTOR SMD 3.3UH 1.44A 7.96MHZ |
| EVAL-ADUC842QSPZ | KIT DEV QUICK START ADUC842 |
| EVAL-ADUC841QSPZ | KIT DEV QUICK START ADUC841 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADUC7023QSPZ1 | 功能描述:BOARD EVAL FOR ADUC7023 RoHS:是 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADuC7023QSPZ2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller, 12-Bit Analog I/O, ARM7TDMI MCU with Enhanced IRQ Handler |
| EVALADUC7023QSPZU1 | 制造商:Analog Devices 功能描述: |
| EVAL-ADUC7024QS | 制造商:Analog Devices 功能描述:QUICK START DEVELOPMENT SYSTEM - Bulk |
| EVAL-ADUC7024QS-U2 | 制造商:Analog Devices 功能描述:QUICK START DEVL SYST EVAL BOARD I.C. - Bulk |
发布紧急采购，3分钟左右您将得到回复。