- 您现在的位置：买卖IC网 > PDF目录17109 > EVAL-ADUC7126QSPZ (Analog Devices Inc)BOARD EVALUATION FOR ADUC7126 PDF资料下载
参数资料
| 型号： | EVAL-ADUC7126QSPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/108页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR ADUC7126 |
| 设计资源： | EVAL-ADUC7126 Schematic ADUC7126 Gerber Files |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC7xxx |
| 类型： | MCU |
| 适用于相关产品： | ADUC7126 |
| 所含物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
ADuC7124/ADuC7126
Data Sheet
Rev. C | Page 40 of 108
on P0.5 (see the General-Purpose Input/Output section) if
enabled in the ADCCON register.
ADCDAT Register
Name:
ADCDAT
Address:
0xFFFF0510
Default Value:
0x00000000
Access:
Read only
ADCDAT is an ADC data result register that holds the 12-bit
ADC result, as shown in Figure 30.
ADCRST Register
Name:
ADCRST
Address:
0xFFFF0514
Default Value:
0x00
Access:
Read/write
ADCRST resets the digital interface of the ADC. Writing any value
to this register resets all the ADC registers to their default values.
ADCGN Register
Name:
ADCGN
Address:
0xFFFF0530
Default Value:
0x0200
Access:
Read/write
ADCGN is a 10-bit gain calibration register.
ADCOF Register
Name:
ADCOF
Address:
0xFFFF0534
Default Value:
0x0200
Access:
Read/write
ADCOF is a 10-bit offset calibration register.
CONVERTER OPERATION
The ADC incorporates a successive approximation (SAR)
architecture involving a charge-sampled input stage. This
architecture can operate in three different modes: differential,
pseudo differential, and single-ended.
Differential Mode
The ADuC7124/ADuC7126 each contains a successive approx-
imation ADC based on two capacitive DACs. Figure 32 and
Figure 33 show simplified schematics of the ADC in acquisition
and conversion phases, respectively. The ADC comprises con-
trol logic, a SAR, and two capacitive DACs. In Figure 32 (the
acquisition phase), SW3 is closed and SW1 and SW2 are in
Position A. The comparator is held in a balanced condition, and
the sampling capacitor arrays acquire the differential signal on
the input.
0912
3
-0
1
7
CAPACITIVE
DAC
CAPACITIVE
DAC
CONTROL
LOGIC
COMPARATOR
SW3
SW1
A
B
SW2
CS
VREF
AIN0
AIN11
MUX
CHANNEL+
CHANNEL–
Figure 32. ADC Acquisition Phase
When the ADC starts a conversion, as shown in Figure 33, SW3
opens, and then SW1 and SW2 move to Position B. This causes
the comparator to become unbalanced. Both inputs are discon-
nected once the conversion begins. The control logic and the
charge redistribution DACs are used to add and subtract fixed
amounts of charge from the sampling capacitor arrays to bring
the comparator back into a balanced condition. When the
comparator is rebalanced, the conversion is complete. The
control logic generates the ADC output code. The output
impedances of the sources driving the VIN+ and VIN– pins must
be matched; otherwise, the two inputs have different settling
times, resulting in errors.
0912
3
-0
1
8
CAPACITIVE
DAC
CAPACITIVE
DAC
CONTROL
LOGIC
COMPARATOR
SW3
SW1
A
B
SW2
CS
VREF
AIN0
AIN11
MUX
CHANNEL+
CHANNEL–
Figure 33. ADC Conversion Phase
Pseudo Differential Mode
In pseudo differential mode, Channel is linked to the
ADCNEG pin of the ADuC7124/ADuC7126. In Figure 34,
ADCNEG is represented as VIN. SW2 switches between A
(Channel) and B (VREF). The ADCNEG pin must be connected
to ground or to a low voltage. The input signal on VIN+ can then
vary from VIN to VREF + VIN. Note that VIN must be chosen so
that VREF + VIN do not exceed AVDD.
0912
3
-0
1
9
CAPACITIVE
DAC
CAPACITIVE
DAC
CONTROL
LOGIC
COMPARATOR
SW3
SW1
A
B
SW2
CS
VREF
AIN0
AIN11
VIN–
MUX
CHANNEL+
CHANNEL–
Figure 34. ADC in Pseudo Differential Mode
相关PDF资料 |
PDF描述 |
|---|---|
| REC5-243.3SRWZ/H4/A | CONV DC/DC 5W 9-36VIN 3.3VOUT |
| EVAL-ADUC7023QSPZ | KIT DEV FOR ADUC7023 QUICK START |
| RPS-1K-6-250/2.0-9 | HEAT SHRINK SLEEVE |
| ECM30DCWH | CONN EDGECARD 60POS DIP .156 SLD |
| SC43B-3R3 | INDUCTOR SMD 3.3UH 1.44A 7.96MHZ |
相关代理商/技术参数 |
参数描述 |
|---|---|
| EVAL-ADUC7128QSPZ | 功能描述:KIT DEV FOR ADUC7128 RoHS:是 类别:编程器，开发系统 >> 通用嵌入式开发板和套件（MCU、DSP、FPGA、CPLD等） 系列:QuickStart™ PLUS 套件 产品培训模块:Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services 特色产品:Blackfin? BF50x Series Processors 标准包装:1 系列:Blackfin® 类型:DSP 适用于相关产品:ADSP-BF548 所含物品:板，软件，4x4 键盘，光学拨轮，QVGA 触摸屏 LCD 和 40G 硬盘 配用:ADZS-BFBLUET-EZEXT-ND - EZ-EXTENDER DAUGHTERBOARDADZS-BFLLCD-EZEXT-ND - BOARD EXT LANDSCAP LCD INTERFACE 相关产品:ADSP-BF542BBCZ-4A-ND - IC DSP 16BIT 400MHZ 400CSBGAADSP-BF544MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF542KBCZ-6A-ND - IC DSP 16BIT 600MHZ 400CSBGAADSP-BF547MBBCZ-5M-ND - IC DSP 16BIT 533MHZ MDDR 400CBGAADSP-BF548BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF547BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF544BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGAADSP-BF542BBCZ-5A-ND - IC DSP 16BIT 533MHZ 400CSBGA |
| EVAL-ADUC7128QSPZ2 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller ARM7TDMI MCU with 12-Bit ADC and DDS DAC |
| EVAL-ADUC7129QSPZ | 制造商:Analog Devices 功能描述:- Bulk |
| EVAL-ADUC812QS | 制造商:Analog Devices 功能描述:DEVELOPMENT KIT SYSTEM |
| EVAL-ADUC812QSP | 制造商:AD 制造商全称:Analog Devices 功能描述:MicroConverter㈢, Multichannel 12-Bit ADC with Embedded Flash MCU |
发布紧急采购，3分钟左右您将得到回复。