参数资料
| 型号： | XRT83SL34IV |
| 厂商： | Exar Corporation |
| 文件页数： | 53/80页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 QUAD 128TQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-LQFP |
| 供应商设备封装： | 128-TQFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页当前第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
XRT83SL34
QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.0
54
D3
NLCD_n
Network Loop-Code Detection:
This bit operates differently in the Manual or the Automatic
Network Loop-Code detection modes.
In the Manual Loop-Code detection mode, (NLCDE1 = “0”
and NLCDE0 = “1” or NLCDE1 = “1” and NLCDE0 = “0”) this
bit gets set to “1” as soon as the Loop-Up (“00001”) or Loop-
Down (“001”) code is detected in the receive data for longer
than 5 seconds. The NLCD bit stays in the “1” state for as long
as the chip detects the presence of the Loop-code in the
receive data and it is reset to “0” as soon as it stops receiving
it. In this mode, if the NLCD interrupt is enabled, the chip will
initiate an interrupt on every transition of the NLCD.
When the Automatic Loop-code detection mode, (NLCDE1
= “1” and NLCDE0 =”1”) is initiated, the state of the NLCD
interface bit is reset to “0” and the chip is programmed to mon-
itor the receive input data for the Loop-Up code. This bit is set
to a “1” to indicate that the Network Loop Code is detected for
more than 5 seconds. Simultaneously the Remote Loop-Back
condition is automatically activated and the chip is pro-
grammed to monitor the receive data for the Network Loop
Down code. The NLCD bit stays in the “1” state for as long as
the Remote Loop-Back condition is in effect even if the chip
stops receiving the Loop-Up code. Remote Loop-Back is
removed if the chip detects the “001” pattern for longer than 5
seconds in the receive data.Detecting the “001” pattern also
results in resetting the NLCD interface bit and initiating an
interrupt provided the NLCD interrupt enable bit is active.
When programmed in Automatic detection mode, the
NLCD interface bit stays “High” for the entire time the Remote
Loop-Back is active and initiate an interrupt anytime the status
of the NLCD bit changes. In this mode, the Host can monitor
the state of the NLCD bit to determine if the Remote Loop-
Back is activated.
RO
0
D2
AISD_n
Alarm Indication Signal Detect: This bit is set to a “1” to indi-
cate All Ones Signal is detected by the receiver. The value of
this bit is based on the current status of Alarm Indication Sig-
nal detector of channel n. If the AISDIE bit is enabled, any
transition on this bit will generate an Interrupt.
RO
0
D1
RLOS_n
Receive Loss of Signal: This bit is set to a “1” to indicate that
the receive input signal is lost. The value of this bit is based on
the current status of the receive input signal of channel n. If the
RLOSIE bit is enabled, any transition on this bit will generate
an Interrupt.
RO
0
D0
QRPD_n
Quasi-random Pattern Detection: This bit is set to a “1” to
indicate the receiver is currently in synchronization with QRSS
pattern. The value of this bit is based on the current status of
Quasi-random pattern detector of channel n. If the QRPDIE bit
is enabled, any transition on this bit will generate an Interrupt.
RO
0
TABLE 24: MICROPROCESSOR REGISTER #5, BIT DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101E28-18SX | CONN RCPT 12POS FREE HNG W/SCKT |
| XRT7300IVTR | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| MS3101E28-18SW | CONN RCPT 12POS FREE HNG W/SCKT |
| XRT73L02MIVTR-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| MS27508E14B5SD | CONN RCPT 5POS BOX MNT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SL34IV-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT83SL38 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL38_07 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER |
| XRT83SL38ES | 功能描述:外围驱动器与原件 - PCI 8 CHT1/E1LIUSH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL38ES-BG | 功能描述:界面开发工具 Eval System for XRT83SL38 Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。