- 您现在的位置：买卖IC网 > PDF目录202515 > VNC1L-1A (Future Technology Devices International Ltd) PDF资料下载
参数资料
| 型号： | VNC1L-1A |
| 厂商： | Future Technology Devices International Ltd |
| 元件分类： | 总线控制器 |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP48 |
| 封装： | 7 X 7 MM, 0.50 MM PITCH, GREEN, LQFP-48 |
| 文件页数： | 6/32页 |
| 文件大小： | 672K |
| 代理商： | VNC1L-1A |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Copyright 2009 Future Technology Devices International Limited
14
Document Reference No.: FT_000030
Vinculum VNC1L Embedded USB Host Controller IC Datasheet Version 2.02
Clearance No.: FTDI# 50
5 Firmware Control Interface
There are three firmware interface options for the command monitor on the combined control and data
interface. The command monitor interface options are UART, FIFO or SPI. The mode of operation is
selected using VNC1L pins 46 and 47.The pin connections used to select the mode of the interface are
shown in Table 5.1:
Pin No.
Mode
47
(ACBUS6)
46
(ACBUS5)
Pull-Up
UART
Pull-Up
Pull-Down
SPI
Pull-Down
Pull-Up
FIFO
Pull-Down
UART
Table 5.1 Combined Interface Selection
Important : Pins ACBUS5 and ACBUS6 should not be tied directly to GND or VCC.
Pins ACBUS5 and ACBUS6 should be pulled high or low using a resistor of around 47k. These pins are
read only at reset, but may then become outputs after the interface choice has been selected. When FIFO
mode is selected ACBUS5 will be used as an output by VNC1L Firmware.
5.1 UART Interface
When the data and control buses are configured in UART mode, the interface implements a standard
asynchronous serial UART port with flow control. The UART can support baud rates from 300baud to
1Mbaud.
Data transfer uses NRZ (Non-Return to Zero) data format consisting of 1 start bit, 7 or 8 data bits, an
optional parity bit, and one or two stop bits. When transmitting the data bits, the least significant bit is
transmitted first. Transmit and receive waveforms are illustrated in Figure 5.1 and Figure 5.2:
.
Figure 5.1 UART Receive Waveform
Figure 5.2 UART Transmit Waveform
Baud rate (default =9600 baud), flow control settings (default = RTS/CTS), number of data bits
(default=8), parity (default is no parity) and number of stop bits (default=1) are all configurable using
the firmware command interface. Please refer to http://www.ftdichip.com (or latest version).
相关PDF资料 |
PDF描述 |
|---|---|
| VND5E012AYTR-E | SPECIALTY ANALOG CIRCUIT, PDSO36 |
| VNL5050S5-E | POWER SUPPLY SUPPORT CKT, PDSO8 |
| VNL5050N3TR-E | POWER SUPPLY SUPPORT CKT, PDSO3 |
| VO27.0000000M0000001 | VCXO, CLOCK, 27 MHz, TTL OUTPUT |
| VP06DDC1R0N999 | 0.3 W, SMPS TRANSFORMER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| VNC1L-1A-REEL | 功能描述:USB 接口集成电路 USB Vinculum Host /Dev Ctrl IC LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| VNC1L-1A-TRAY | 功能描述:USB 接口集成电路 USB Vinculum Host /Dev Ctrl IC LQFP-48 RoHS:否 制造商:Cypress Semiconductor 产品:USB 2.0 数据速率: 接口类型:SPI 工作电源电压:3.15 V to 3.45 V 工作电源电流: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:WLCSP-20 |
| VNC2 | 制造商:FTDI 制造商全称:FTDI 功能描述:VNC2 Debug Module |
| VNC2 DEBUG MODULE | 功能描述:界面开发工具 USB Vinculum-II Debug/Programmer Mod RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| VNC214B-15A-1D | 制造商:SMC Corporation of America 功能描述:Valve, media, solenoid, body port, 1/2 inch |
发布紧急采购，3分钟左右您将得到回复。