- 您现在的位置：买卖IC网 > PDF目录19188 > MMA7660FCT (Freescale Semiconductor)ACCELEROMETER 3X3 DGTL 10-DFN PDF资料下载
参数资料
| 型号： | MMA7660FCT |
| 厂商： | Freescale Semiconductor |
| 文件页数： | 17/35页 |
| 文件大小： | 0K |
| 描述： | ACCELEROMETER 3X3 DGTL 10-DFN |
| 特色产品： | MMA7660 Digital Output Accelerometer |
| 标准包装： | 490 |
| 轴： | X，Y，Z |
| 加速范围： | ±1.5g |
| 灵敏度： | 21.33 计数/g |
| 电源电压： | 2.4 V ~ 3.6 V |
| 输出类型： | 数字 |
| 接口： | I²C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFDFN |
| 供应商设备封装： | 10-DFN（3x3） |
| 产品目录页面： | 2805 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
$07: Mode Register (Read/Write)
MODE
D7
IAH
0
D6
IPP
0
D5
SCPS
0
D4
ASE
0
D3
AWE
0
D2
TON
0
D1
-
0
D0
MODE
0
NOTE: Writing to the Mode register resets sleep timing, and clears the XOUT, YOUT, ZOUT, TILT registers.Reading to
the Mode register resets sleep timing.
NOTE: The device must be placed in Standby Mode to change the value of the registers.
Table 10. Modes
Mode of Operation
Standby Mode
Test Mode
Active Mode
D0 - MODE
0
0
1
D2 - TON
0
1
0
NOTE: The device can only enter into Test Mode, when the previous mode was Standby Mode. If the device was in
Active mode, set MMA766FC to Standby Mode (MODE = TON = 0), then enter Test Mode (MODE = 0, TON = 1).
MODE
0: Standby mode or Test Mode depending on state of TON
1: Active mode
Existing state of TON bit must be 0, to write MODE = 1. Test
Mode must not be enabled.
MMA7660FC always enters Active Mode using the samples
per second specified in AMSR[2:0] of the SR (0x08) register.
When MMA7660FC enters Active Mode with
[ASE:AWE] = 11, MMA7660FC operates Auto-Sleep
functionality first.
TON
0: Standby Mode or Active Mode depending on state of
MODE
1: Test Mode
Existing state of MODE bit must be 0, to write TON = 1.
Device must be in Standby Mode.
In Test Mode (TON = 1), the data in the XOUT, YOUT and
ZOUT registers is not updated by measurement, but is
instead updated by the user through the I 2 C interface for test
purposes. Changes to the XOUT, YOUT and ZOUT register
data is processed by MMA7660FC to change orientation
status and generate interrupts just like Active Mode.
Debounce filtering and shake detection are disabled in Test
Mode.
AWE
0: Auto-Wake is disabled
1: Auto-Wake is enabled.
When Auto-Wake functionality is operating, the AWSRS bit is
the SRST register is set and the device uses the samples per
second specified in AWSR[1:0] of the SR (0x08) register.
When MMA7660FC automatically exits Auto-Wake by a
ASE
0: Auto-Sleep is disabled
1: Auto-Sleep is enabled
When Auto-Sleep functionality is operating, the AMSRS bit is
the SRST register is set and the device uses the samples per
second specified in AMSR[2:0] of the SR (0x08) register.
When MMA7660FC automatically exits Auto-Sleep because
the Sleep Counter times out, the device will then switch to the
samples per second specified in AWSR[1:0] of the SR
register. If AWE = 1, then Auto-Wake functionality is now
enabled ( Table 11 ).
SCPS
0: The prescaler is divide-by-1. The 8-bit internal Sleep
Counter input clock is the samples per second set by
AMSR[2:0], so the clock range is 120 Hz to 1 Hz depending
on AMSR[2:0] setting. Sleep Counter timeout range is
256 times the prescaled clock (see Table 12 ).
1: Prescaler is divide-by-16. The 8-bit Sleep Counter input
clock is the samples per second set by AMSR[2:0] divided by
16, so the clock range is 4 Hz to 0.0625 Hz depending on
AMSR[2:0] setting. Sleep Counter timeout range is 256 times
the prescaled clock (see Table 12 ).
IPP
0: Interrupt output INT is open-drain.
1: Interrupt output INT is push-pull
NOTE: Do NOT connect pull-up resistor from INT to
higher voltage than DVDD.
IAH
0: Interrupt output INT is active low
1: Interrupt output INT is active high
selected interrupt, the device will then switch to the samples
per second specified in AMSR[2:0] of the SR (0x08) register.
If ASE = 1, then Auto-Sleep functionality is now enabled
The active interrupt condition (IRQ = 0 if IAH = 0, IRQ = 1 if IAH = 1) is released during the acknowledge bit of the slave address
transmission of the first subsequent I 2 C to the device after the interrupt was asserted.
MMA7660FC
Sensors
17
Freescale Semiconductor, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| DPL04 | PIANO STYLE DIP SWITCH |
| 551-0307F | LED 3MM HIGH EFF YELLOW |
| 90GB10LT | SWITCH 10POS DIP AUTODIP |
| 550-0207F | LED 5MM RT ANGLE GREEN PC MNT |
| A6SN-4101-P | SWITCH DIP 4POS FLUSH ACT SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MMA7660FCT | 制造商:Freescale Semiconductor 功能描述:IC 3 AXIS ACCELEROMETER ?1.5G DFN-10 |
| MMA8104EG | 功能描述:加速计 - 板上安装 SOURCE ONLY RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MMA8104EGR2 | 功能描述:加速计 - 板上安装 Z-AXIS 40G W/CAP BOND RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MMA8104KEG | 功能描述:加速计 - 板上安装 SOURCE ONLY RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| MMA8104KEGR2 | 功能描述:加速计 - 板上安装 Z-AXIS 40G W/CAP BOND RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。