- 您现在的位置：买卖IC网 > PDF目录14459 > LTC3546EUFD#PBF (Linear Technology)IC REG BUCK SYNC ADJ 1A/2A 28QFN PDF资料下载
参数资料
| 型号： | LTC3546EUFD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 23/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1A/2A 28QFN |
| 标准包装： | 73 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz，750kHz ~ 4MHz |
| 电流 - 输出： | 1A，2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 28-QFN（4x5） |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页
LTC3546
APPLICATIONS INFORMATION
C OUT1 =
= 20.5μF
? 0.8A ?
? 0.8A
C OUT1 =
= 64.2μF
? 2.5A ?
? 2.5A
operating frequency of 1.5MHz and assumes roughly a
300mA/A load step.
22μF 280mA
A 300mA
A
22μF 875mA
A 300mA
A
The closest values are 22μF and 68μF.
The output voltages can now be programmed by choos-
ing the values of R1, R2, R3, and R4. To maintain high
efficiency, the current in these resistors should be kept
small. Choosing 2μA with the 0.6V feedback voltages
makes R2 and R4 equal to 300k. A close standard 1%
resistor is 301k. This then makes R1 = 300k. A close
standard 1% is 301k. R3 then equals 600k. A close 1%
resistor is 604k.
The compensation should be optimized for these com-
ponents by examining the load step response but a good
place to start for the LTC3546 is with a 13k Ω and 1000pF
filter on both I TH1 and I TH2 . The output capacitor may
need to be increased depending on the actual transient
during a load step.
The PGOOD pin is a common drain output and requires a
pull-up resistor. A 100k resistor is used for adequate speed.
Figure 9 shows a complete schematic for this design.
Board Layout Considerations
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of
the LTC3546. These items are also illustrated graphically
in the layout diagram of Figure 7. Check the following in
your layout.
1. Make sure SW1, SW2A, SW2B and SW1D are connected
on the PC board through a wide piece of copper.
2. All, or part, of C IN should connect from Pin 9 to Pin 14
on the same side of the PC board as the chip and as
close to the chip as possible, where the SW traces will go
directly under the capacitor. C IN provides the AC current
to the internal power MOSFETs and their drivers.
3. Are the respective C OUT , L closely connected? The (–)
plate of C OUT1 returns current to PGND1, and the (–)
plate of C OUT2 returns current to the PGND2. The (–)
plate of C IN should also return current to PGND1 and
PGND2.
4. The resistor divider, R1 and R2, must be connected
between the (+) plate of C OUT1 and a ground line ter-
minated near GNDA. The resistor divider R3 and R4,
must be connected between the (+) plate of C OUT2 and
the ground connection terminated to the GNDA pin.
The feedback signals V FB1 and V FB2 should be routed
away from noise components and traces, such as the
SW lines, and its trace should be minimized.
5. When using the R FREQ resistor, the ground connection
of the resistor should be terminated to the GNDA pin.
When using the internal PLL, the ground connection of
the R-C compensation network should be terminated
to the GNDA pin.
6. Keep sensitive components away from the SW pins.
The input capacitor C IN , the compensation capacitors
C FF1 , C FF2 , C ITH1 , and C ITH2 and all resistors R1, R2,
R3, R4, R ITH1 and R ITH2 should be routed away from
the SW traces and the inductors L1 and L2.
7. A ground plane is preferred, but if not available, keep
the signal and power grounds segregated with small
signal components returning to the SGND pin at one
point which is then connected to the PGND1/PGND2/
PGND1D/GNDD pins.
8. Flood all unused areas on all layers with copper. Flooding
with copper will reduce the temperature rise of power
components. These copper areas should be connected
to the Exposed Pad (Pin 29).
23
For more information www.linear.com/3546
3546fc
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1514IS8-5#PBF | IC REG MULTI CONFIG 5V 8SOIC |
| LT3510IFE#PBF | IC REG BUCK ADJ 2A DL 20TSSOP |
| VE-J2H-EX-B1 | CONVERTER MOD DC/DC 52V 75W |
| VE-J23-EX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VE-J22-EX-B1 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3546EUFDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
发布紧急采购，3分钟左右您将得到回复。