- 您现在的位置：买卖IC网 > PDF目录14459 > LTC3546EUFD#PBF (Linear Technology)IC REG BUCK SYNC ADJ 1A/2A 28QFN PDF资料下载
参数资料
| 型号： | LTC3546EUFD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 22/30页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK SYNC ADJ 1A/2A 28QFN |
| 标准包装： | 73 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 0.6 V ~ 5 V |
| 输入电压： | 2.25 V ~ 5.5 V |
| PWM 型： | 电流模式，混合 |
| 频率 - 开关： | 2.25MHz，750kHz ~ 4MHz |
| 电流 - 输出： | 1A，2A |
| 同步整流器： | 是 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 28-QFN（4x5） |
| 产品目录页面： | 1335 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页第28页第29页第30页
LTC3546
APPLICATIONS INFORMATION
L1 =
? ? 1 ?
? = 2μH
? ? 1 ?
? = 0.78μH
1.8V ? 1.8V ?
1.5MHz ? 875mA ?
4.2V ?
tion to exceed the maximum junction temperature of the
part. In a majority of applications, the LTC3546 does not
dissipate much heat due to its high efficiency. However, in
applications where the LTC3546 is running at high ambient
temperature with low supply voltage and high duty cycles,
such as in dropout, the heat dissipated may exceed the
maximum junction temperature of the part. If the junction
temperature reaches approximately 150°C, both switches
in both regulators will be turned off and the SW nodes will
become high impedance.
To avoid the LTC3546 from exceeding the maximum junc-
tion temperature, the user will need to do some thermal
analysis. The goal of the thermal analysis is to determine
whether the power dissipated exceeds the maximum
junction temperature of the part. The temperature rise is
given by:
T RISE = P D ? θ JA
where P D is the power dissipated by the regulator and θ JA
is the thermal resistance from the junction of the die to
the ambient temperature.
The junction temperature, T J , is given by:
T J = T RISE + T AMBIENT
As an example, consider the case when the LTC3546 is
in dropout in both regulators at an input voltage of 3.3V
with load currents of 3A (SW1D externally connected to
SW2) and 1A. From the Typical Performance Character-
istics graph of Switch Resistance, the R DS(ON) resistance
of the 3A P-channel switch parallel combination of SW2
and SW1D is 0.06 Ω and the R DS(ON) of the 1A P-channel
switch is 0.18 Ω . The power dissipated by the part is:
P D = I1 2 R DS(ON)1 + I2 2 R DS(ON)2
P D = 3 2 ? 0.064 + 1 2 ? 0.19
P D = 0.77W
The UFD package junction-to-ambient thermal resistance,
θ JA , is about 34°C/W. Therefore, the junction temperature
of the regulator operating in a 85°C ambient temperature
is approximately:
T J = 0.77 ? 34 + 85
T J = 111.2°C
This junction temperature is obtained from an R DS(ON) at
25°C. At 125°C the R DS(ON) increases by about 30%. This
will put the junction temperature at 122°C. If the supply is
lower, like 2.25V, the R DS(ON) is higher still. Special care
needs to be taken if the part is expected to be operating
in dropout so that the maximum junction temperature of
125°C is not exceeded.
Design Example
As a design example, consider using the LTC3546 in a
portable application with a Li-Ion battery. The battery
provides a V IN = 2.25V to 4.2V. One output requires 1.8V
at 2.5A in active mode, and 1mA in standby mode. The
other output requires 1.2V at 800mA in active mode,
and 500μA in stand-by mode. Since both loads still need
power in stand-by, Burst Mode operation is selected for
good low load efficiency.
First, determine what frequency should be used. Higher
frequency results in a lower inductor value for a given Δ I L
( Δ I L is estimated as 0.35I LOAD(MAX) ). Reasonable values
for wire wound surface mount inductors are in the 1μH
and up. Look at the different frequencies with the Δ I L =
0.35I LOAD(MAX) .
CONVERTER OUTPUT I LOAD(MAX) Δ I L
SW2/SW1D, 1.2V 2.5A 875mA
SW1, 1.8V 800mA 280mA
Using the 1.5MHz frequency setting (FREQ = 143k to GNDA)
we get the following equations for L1 and L2.
1.2V ? 1.2V ?
1.5MHz ? 280mA ? 4.2V ?
L2 =
Use 1μH and 2.2μH.
C OUT selection is typically based on load step rather
than the ripple requirements. The minimum required
capacitance will increase with a decrease in compensa-
tion loop bandwidth and/or increases in maximum load
step or output voltage tolerance. A good starting point is
about 22μF per ampere of output current for a nominal
22
For more information www.linear.com/3546
3546fc
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1514IS8-5#PBF | IC REG MULTI CONFIG 5V 8SOIC |
| LT3510IFE#PBF | IC REG BUCK ADJ 2A DL 20TSSOP |
| VE-J2H-EX-B1 | CONVERTER MOD DC/DC 52V 75W |
| VE-J23-EX-B1 | CONVERTER MOD DC/DC 24V 75W |
| VE-J22-EX-B1 | CONVERTER MOD DC/DC 15V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC3546EUFDTRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFE#PBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFE#TRPBF | 功能描述:IC REG BUCK SYNC ADJ DL 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 设计资源:Design Support Tool 标准包装:1 系列:- 类型:升压（升压） 输出类型:固定 输出数:1 输出电压:3V 输入电压:0.75 V ~ 2 V PWM 型:- 频率 - 开关:- 电流 - 输出:100mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-5 细型，TSOT-23-5 包装:剪切带 (CT) 供应商设备封装:TSOT-23-5 其它名称:AS1323-BTTT-30CT |
| LTC3546IFEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
| LTC3546IFETRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Synchronous, 3A/1A or 2A/2A Confi gurable Step-Down DC/DC Regulator |
发布紧急采购，3分钟左右您将得到回复。