参数资料
| 型号： | XRT83SL216IB |
| 厂商： | Exar Corporation |
| 文件页数： | 11/42页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH E1 16CH 289STBGA |
| 标准包装： | 84 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 16/16 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 289-LFBGA |
| 供应商设备封装： | 289-STBGA（15x15） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
XRT83SL216
17
REV. 1.0.0
16-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT
1.4.1
RLOS (Receiver Loss of Signal)
The XRT83SL216 supports both G.775 or ETSI-300-233 RLOS detection scheme.
In G.775 mode, RLOS is declared when the received signal is less than 320mV for more than 32 consecutive
pulse periods (typical). The device clears RLOS when the receive signal achieves 12.5% ones density with no
more than 15 consecutive zeros in a 32 bit sliding window and the signal level exceeds 550mV (typical).
In ETSI-300-233 mode the device declares RLOS when the input level drops below 320mV (typical) for more
than 2048 pulse periods (1msec). The device clears RLOS when the receive signal achieves 12.5% ones
density with no more than 15 consecutive zeros in a 32 bit sliding window and the signal level exceeds 550mV
(typical).
1.4.2
AIS (Alarm Indication Signal)
The XRT83SL216 adheres to ITU-T G.775 or ETSI-300-233 specifications for an all ones pattern detection by
programming the appropriate channel register. The alarm indication signal is set to "1" if an all ones pattern is
detected. In G.775 mode, AIS is defined as 2 or less zeros in 2 consecutive double frame (512-bit window)
periods. AIS will clear when the incoming signal has 3 or more zeros in the same time period. In ETSI-300-233
mode, AIS is defined as less than 3 zeros in a 512-bit window.
1.4.3
LCV (Line Code Violation Detection)
In HDB3 mode, the LCV pin will be set to "High" if the receiver detects excessive zero’s, bipolar violations or
HDB3 code violations. If the device is configured in AMI mode, any bipolar violations will cause the LCV pin to
go "High".
1.5
Receive Jitter Attenuator
The jitter attenuator can be configured in the receive path to reduce phase and frequency jitter in the recovered
clock. The jitter attenuator uses a data FIFO (First In First Out) with a programmable depth of 32-bit or 64-bit. If
the LIU is used for line synchronization (loop timing systems), the JA should be enabled. When the Read and
Write pointers of the FIFO are within 2-Bits of over-flowing or under-flowing, the bandwidth of the jitter
attenuator is widened to track the short term input jitter, thereby avoiding data corruption. When this condition
occurs, the jitter attenuator will not attenuate input jitter until the Read/Write pointer’s position is outside the 2-
Bit window. The JA has a typical clock delay equal to of the FIFO bit depth.
NOTE: If the LIU is used in a multiplexer/mapper application where stuffing bits are typically removed, the JA can be
configured in the transmit path to smooth out the gapped clock. See the Transmit Section of this datasheet.
1.6
HDB3 Decoder
In single rail mode, RPOS is the output of decoded AMI or HDB3 signals and RNEG is the LCV output. HDB3
data is defined as any block of 4 successive zeros replaced with OOOV or BOOV, so that two successive V
pulses are of opposite polarity to acheive zero DC offset. If the HDB3 decoder is selected, the receive path
removes the V and B pulses so that the original data is output to RPOS.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-233-IU-F1 | CONVERTER MOD DC/DC 24V 200W |
| VI-B6T-MX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| D38999/26WA98SD | CONN PLUG 3POS STRAIGHT W/SCKT |
| VI-231-IU-F3 | CONVERTER MOD DC/DC 12V 200W |
| MS27468T21F39P | CONN RCPT 39POS JAM NUT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SL216IB-F | 功能描述:接口 - 专用 RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| XRT83SL28 | 制造商:EXAR 制造商全称:EXAR 功能描述:8-CHANNEL E1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL28ES | 功能描述:外围驱动器与原件 - PCI 8 CH E1 LIU SH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL28IV | 功能描述:接口 - 专用 . . RoHS:否 制造商:Texas Instruments 产品类型:1080p60 Image Sensor Receiver 工作电源电压:1.8 V 电源电流:89 mA 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:BGA-59 |
| XRT83SL28IV-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。