参数资料
| 型号： | XRT73L03BIV |
| 厂商： | Exar Corporation |
| 文件页数： | 49/61页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 3CH 120LQFP |
| 标准包装： | 72 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 3/3 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 120-LQFP |
| 供应商设备封装： | 120-LQFP（14x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页当前第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页
XRT73L03B
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
REV. 1.0.1
51
When the Transmit Drive Monitor circuitry within a
given line is connected to the line, as illustrated in
Figure 36, then it monitors the line for transitions. As
long as the Transmit Drive Monitor circuitry detects
transitions on the line via the MTIP_(n) and
MRing_(n) pins, then it keeps the DMO (Drive Moni-
tor Output) signal "Low". However, if the Transmit
Drive Monitor circuit detects no transitions on the line
for 128+32 TxClk periods, then the DMO (Drive Moni-
tor Output) signal toggles "High".
NOTE: The Transmit Drive Monitor circuit does not have to
be used to operate the Transmit Section of the XRT73L03B.
This is purely a diagnostic feature.
4.6
THE TAOS (TRANSMIT ALL ONES) FEATURE
The XRT73L03B can command any channel to trans-
mit an all “1’s" pattern onto the line by toggling a sin-
gle input pin or by setting a single bit-field within one
of the Command Registers to "1".
NOTE: When this feature is activated, the Transmit Section
of the configured channel overwrites the Terminal Equip-
ment data with this all “1’s" pattern.
a. Operating in the Hardware Mode
Configure Channel(n) to transmit an all “1’s" pattern
by toggling the TAOS_(n) input pin “High". Terminate
the all “1’s" pattern by toggling the TAOS_(n) input pin
“Low".
b. Operating in the HOST Mode
Configure Channel(n) to transmit an all “1’s" pattern
by writing to Command Register CR1-(n) and setting
the TAOS_(n) bit-field (bit D3) to "1".
Terminate the all “1’s" pattern by writing to Command
Register CR1-(n) and setting the TAOS_(n) bit-field
(D3) to "0".
5.0
THE MICROPROCESSOR SERIAL INTER-
FACE
The on-chip Command Registers of XRT73L03B
DS3/E3/STS-1 Line Interface Unit IC are used to con-
figure the XRT73L03B into a wide-variety of modes.
This section discusses the following:
1. The description of the Command Registers.
2. A description on how to use the Microprocessor
Serial Interface.
5.1
DESCRIPTION OF THE COMMAND REGISTERS
(repeated as Table 7), lists the Command Registers,
their Addresses and their bit-formats.
FIGURE 36. THE XRT73L03B EMPLOYING THE TRANSMIT DRIVE MONITOR FEATURES
R1 = 31.6
R2 = 31.6
Channel (n)
TxPOS_(n)
TxNEG_(n)
TxLineClk_(n)
TTIP_(n)
TRing_(n)
TPData_(n)
TNData_(n)
TxClk_(n)
Only One Channel Shown
1:1
J1
BNC
MTIP_(n)
MRing_(n)
R3 = 270
R4 = 270
COMMAND REGISTER CR1-(n)
D4
D3
D2
D1
D0
TxOFF_(n) TAOS_(n) TxClkINV_(n) TxLEV_(n) TxBIN_(n)
0
1X
X
相关PDF资料 |
PDF描述 |
|---|---|
| IDT72825LB15PF | IC FIFO SYNC DL 1024X18 128TQFP |
| MS27472T12F35P | CONN RCPT 22POS WALL MNT W/PINS |
| IDT72V3650L6PFG8 | IC FIFO SS 2048X36 6NS 128-TQFP |
| MS3100A28-2P | CONN RCPT 14POS WALL MNT W/PINS |
| MS27473E10F35SA | CONN PLUG 13POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT73L03BIV-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT73L03IV | 制造商:EXAR 制造商全称:EXAR 功能描述:3 CHANNEL E3/DS3/STS-1 LINE INTERFCE UNIT |
| XRT73L03IVS | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Telecommunication IC |
| XRT73L04A | 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
| XRT73L04AIV | 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT |
发布紧急采购，3分钟左右您将得到回复。