参数资料
| 型号： | XRT7300IVTR |
| 厂商： | Exar Corporation |
| 文件页数： | 55/55页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| 标准包装： | 1,000 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-TQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
5
16
STS-1/DS3
I
STS-1/DS3 Select Input:
A “High” on this pin configures the Clock Recovery Phase Locked Loop to set its
VCO Center frequency to around 51.84 MHz (optimal for SONET STS-1 opera-
tions). A “Low” on this pin configures the Clock Recovery Phase Locked Loop to
set its VCO Center frequency to around 44.736 MHz (optimal for DS3 opera-
tions).
NOTES:
1. The XRT7300 ignores this pin if the E3 pin (pin 17) is set to “1”.
2. This input pin is ignored if the XRT7300 is operating in the HOST Mode.
3. Tie this pin to GND if the XRT7300 is going to be operating in the HOST
Mode.
17
E3
I
E3 Select Input:
A “High” on this pin configures the XRT7300 to operate in the E3 Mode.
A “Low” on this pin configures the XRT7300 to check the state of the STS-1/DS3
input pin.
NOTES:
1. This input pin is ignored if the XRT7300 is operating in the HOST Mode.
2. Tie this pin to GND if the XRT7300 is going to be operating in the HOST
Mode.
18
HOST/HW
I
HOST/HW Mode Select:
This input pin is used to enable or disable the Microprocessor Serial Interface
(e.g., consisting of the SDI, SDO, SCLK, CS and REGRESET pins).
Setting this input pin “High” enables the Microprocessor Serial Interface (e.g.
configures the XRT7300 to operate in the HOST Mode). In this mode, the
XRT7300 is configured by writing data into the on-chip Command Registers via
the Microprocessor Serial Interface. When the XRT7300 is operating in the
HOST Mode, it ignores the states of many of the discrete input pins.
Setting this input pin “Low” disables the Microprocessor Serial Interface (e.g.,
configures the XRT7300 to operate in the Hardware Mode). In this mode, many
of the external input control pins are functional.
19
SDI/
(LOSMUTEN)
I
Serial Data Input for the Microprocessor Serial Interface (HOST Mode) or
MUTE-upon-LOS Enable Input (Hardware Mode):
The function of this input pin depends upon whether the XRT7300 is operating in
the HOST or the Hardware Mode.
Serial Data Input for the Microprocessor Serial Interface (HOST Mode):
This pin is used to read or write data into the Command Registers of the Micro-
processor Serial Interface. The Read/Write bit, the Address Values of the Com-
mand Registers and Data Value to be written during Write Operations are
applied to this pin.
This input is sampled on the rising edge of the SCLK pin (pin 21).
MUTE-upon-LOS Enable Input (Hardware Mode):
When in the Hardware Mode, this input pin is used to configure the XRT7300 to
MUTE the recovered data via the RPOS and RNEG output pins whenever it
declares an LOS condition.
Setting this input pin “High” configures the XRT7300 to automatically pull the
RPOS and RNEG output pins to GND whenever it is declaring an LOS condition,
thereby MUTing the data being output to the Terminal Equipment.
Setting this input pin “Low” configures the XRT7300 to NOT automatically MUTE
the recovered data whenever an LOS condition is declared.
PIN DESCRIPTION
PIN #SYMBOL
TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101E28-18SW | CONN RCPT 12POS FREE HNG W/SCKT |
| XRT73L02MIVTR-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| MS27508E14B5SD | CONN RCPT 5POS BOX MNT W/SCKT |
| MS3100R22-15S | CONN RCPT 6POS WALL MNT W/SCKT |
| MS27467E15F97P | CONN PLUG 12POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT7300IVTR-F | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| XRT7302IV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面开发工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。