参数资料
| 型号： | XRT7300IVTR |
| 厂商： | Exar Corporation |
| 文件页数： | 35/55页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 SGL 44TQFP |
| 标准包装： | 1,000 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LQFP |
| 供应商设备封装： | 44-TQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
XRT7300
E3/DS3/STS-1 LINE INTERFACE UNIT
REV. 1.1.2
36
4.0
DIAGNOSTIC FEATURES OF THE XRT7300
The XRT7300 supports equipment diagnostic activi-
ties by supporting the following Loop-Back modes in
the chip:
Analog Local Loop-Back
Digital Local Loop-Back
Remote Loop-Back.
4.1
THE ANALOG LOCAL LOOP-BACK MODE
When the XRT7300 is configured to operate in the
Analog Local Loop-Back Mode, the XRT7300 ignores
any signals that are input to the RTIP and RRING in-
put pins. The Transmitting Terminal Equipment trans-
mits clock and data into the XRT7300 via the TPDA-
TA, TNDATA and TCLK input pins. This data is pro-
cessed through the Transmit Clock Duty Cycle Adjust
PLL and the HDB3/B3ZS Encoder. Finally, this data
outputs to the line via the TTIP and TRING output
pins and is looped back into the AGC/Receive Equal-
izer Block. Consequently, this data is also processed
through the Receive Section of the XRT7300. After
this post-loop-back data has been processed through
the Receive Section it outputs to the Near-End Re-
ceiving Terminal Equipment via the RPOS, RNEG,
RCLK1 and RCLK2 output pins.
Figure 28 illustrates the path that the data takes when
the chip is configured to operate in the Analog Local
Loop-Back Mode.
The XRT7300 can be configured to operate in the An-
alog Local Loop-Back Mode by employing either one
of the following two steps:
FIGURE 26. THE TYPICAL INTERFACE FOR THE TRANSMISSION OF DATA IN A SINGLE-RAIL FORMAT FROM THE
RECEIVE SECTION OF THE XRT7300 TO THE RECEIVING TERMINAL EQUIPMENT
Terminal
Equipment
(E3/DS3 or STS-1
Framer)
Exar E3/DS3/STS-1 LIU
Receive
Logic
Block
RxPOS
RCLK1, 2
RPOS
RCLK1, 2
FIGURE 27. THE BEHAVIOR OF THE RPOS AND RCLK1 OUTPUT SIGNALS WHILE THE XRT7300 IS TRANSMITTING
SINGLE-RAIL DATA TO THE RECEIVING TERMINAL EQUIPMENT
RCLK1
RPOS
相关PDF资料 |
PDF描述 |
|---|---|
| MS3101E28-18SW | CONN RCPT 12POS FREE HNG W/SCKT |
| XRT73L02MIVTR-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
| MS27508E14B5SD | CONN RCPT 5POS BOX MNT W/SCKT |
| MS3100R22-15S | CONN RCPT 6POS WALL MNT W/SCKT |
| MS27467E15F97P | CONN PLUG 12POS STRAIGHT W/PINS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT7300IVTR-F | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| XRT7302IV | 制造商:未知厂家 制造商全称:未知厂家 功能描述:PCM Transceiver |
| XRT73L00 | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00A | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73L00AES | 功能描述:界面开发工具 Eval System for XRT73L00A Series RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
发布紧急采购，3分钟左右您将得到回复。