- 您现在的位置：买卖IC网 > PDF目录19364 > LT3799EMSE#PBF (Linear Technology)IC LED DRIVER TRIAC DIM 16-MSOP PDF资料下载
参数资料
| 型号： | LT3799EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 7/20页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER TRIAC DIM 16-MSOP |
| 产品培训模块： | LT3799 Offline Isolated Flyback LED Controller |
| 特色产品： | LT3799 Isolated LED Controller |
| 标准包装： | 37 |
| 拓扑： | 交直流离线开关，反激式，PFC |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 通用 |
| 频率： | 25kHz ~ 300kHz |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 相关产品： | 732-3197-ND - TRANSFORMER FLYBACK LT3799 732-3196-ND - TRANSFORMER FLYBACK LT3799 732-3195-ND - TRANSFORMER FLYBACK LT3799 732-3194-ND - TRANSFORMER FLYBACK LT3799 732-3193-ND - TRANSFORMER FLYBACK LT3799 732-3192-ND - TRANSFORMER FLYBACK LT3799 732-3191-ND - TRANSFORMER FLYBACK LT3799 732-2959-ND - TRANS OFFLINE600UH LT3799 LT4180 732-2898-ND - IND TOROID LT3799 NCL30000 750UH |
LT3799
PIN FUNCTIONS
CTRL1, CTRL2, CTRL3 (Pin 1, Pin 2, Pin 3): Current Output
Adjustment Pins. These pins control the output current.
The lowest value of the three CTRL inputs is compared to
the negative input of the operational amplifier. Due to the
unique nature of the LT3799 control loop, the maximum
current does not directly correspond to the V CTRL voltages.
V REF (Pin 4): Voltage Reference Output Pin, Typically 2V.
This pin drives a resistor divider for the CTRL pin, either
for analog dimming or for temperature limit/compensation
of LED load. Can supply up to 200μA.
FAULT (Pin 5): Fault Pin. An open-collector pull-down on
FAULT asserts if FB is greater than 1.25V with the CT pin
higher than 1.25V.
CT (Pin 6): Timer Fault Pin. A capacitor is connected
between this pin and ground to provide an internal timer
for fault operations. During start-up, this pin is pulled to
ground and then charged with a 10μA current. Faults related
to the FB pin will be ignored until the CT pin reaches 1.25V.
If a fault is detected, the controller will stop switching and
begin to discharge the CT capacitor with a 200nA pull-down
current. When the pin reaches 240mV, the controller will
start to switch again.
COMP + , COMP – (Pin 7, Pin 8): Compensation Pins for
Internal Error Amplifier. Connect a capacitor between these
two pins to compensate the internal feedback loop.
FB (Pin 9): Voltage Loop Feedback Pin. FB is used to
detect open LED conditions by sampling the third winding
voltage. An open LED condition is reported if the CT pin
and the FB pin are higher than 1.25V.
DCM (Pin 10): Discontinuous Conduction Mode Detection
Pin. Connect a capacitor and resistor in series with this
pin to the third winding.
V IN (Pin 11): Input Voltage. This pin supplies current to
the internal start-up circuitry and to the INTV CC LDO. This
pin must be locally bypassed with a capacitor. A 25V shunt
regulator is internally connected to this pin.
INTV CC (Pin 13): Regulated Supply for Internal Loads
and GATE Driver. Supplied from V IN and regulates to 10V
(typical). INTV CC must be bypassed with a 4.7μF capacitor
placed close to the pin.
GATE (Pin 14): N-Channel MOSFET Gate Driver Output.
Switches between INTV CC and GND. This pin is pulled to
GND during shutdown state.
SENSE (Pin 15): The Current Sense Input for the Control
Loop. Kelvin connect this pin to the positive terminal of
the switch current sense resistor, R SENSE , and the source
of the N-channel MOSFET. The negative terminal of the
current sense resistor should be connected to the GND
plane close to the IC.
V IN_SENSE (Pin 16): Line Voltage Sense Pin. The pin is used
for sensing the AC line voltage to perform power factor
correction. Connect the output of a resistor divider from
the line voltage to this pin. The voltage on this pin should
be between 1.25V to 1.5V at the maximum input voltage.
GND (Exposed Pad Pin 17): Ground. The exposed pad
of the package provides both electrical contact to ground
and good thermal contact to the printed circuit board.
The exposed pad must be soldered to the circuit board
for proper operation.
3799fa
7
相关PDF资料 |
PDF描述 |
|---|---|
| GEA24DTMS | CONN EDGECARD 48POS R/A .125 SLD |
| AGL060V5-VQG100I | IC FPGA IGLOO 1.5V 100VQFP IND |
| SAA7706H/N210S,557 | IC DSP CAR RADIO 80QFP |
| SAA7706H/N107S,557 | IC DSP CAR RADIO 80QFP |
| MC78M12CDTRK | IC REG LDO 12V .5A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3799IMSE#PBF | 功能描述:IC LED DRIVER TRIAC DIM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| LT3799IMSE#PBF | 制造商:Linear Technology 功能描述:IC LED DRVR MSOP-16 制造商:Linear Technology 功能描述:IC, LED DRVR, MSOP-16 |
| LT3799IMSE#TRPBF | 功能描述:IC LED DRIVER TRIAC DIM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3799IMSE-1#PBF | 功能描述:IC LED CTLR ISO ACT PFC 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3799IMSE-1#TRPBF | 功能描述:IC LED CTLR ISO ACT PFC 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。