- 您现在的位置：买卖IC网 > PDF目录19364 > LT3799EMSE#PBF (Linear Technology)IC LED DRIVER TRIAC DIM 16-MSOP PDF资料下载
参数资料
| 型号： | LT3799EMSE#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/20页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER TRIAC DIM 16-MSOP |
| 产品培训模块： | LT3799 Offline Isolated Flyback LED Controller |
| 特色产品： | LT3799 Isolated LED Controller |
| 标准包装： | 37 |
| 拓扑： | 交直流离线开关，反激式，PFC |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 通用 |
| 频率： | 25kHz ~ 300kHz |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TFSOP（0.118"，3.00mm 宽）裸露焊盘 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
| 包装： | 管件 |
| 工作温度： | -40°C ~ 125°C |
| 相关产品： | 732-3197-ND - TRANSFORMER FLYBACK LT3799 732-3196-ND - TRANSFORMER FLYBACK LT3799 732-3195-ND - TRANSFORMER FLYBACK LT3799 732-3194-ND - TRANSFORMER FLYBACK LT3799 732-3193-ND - TRANSFORMER FLYBACK LT3799 732-3192-ND - TRANSFORMER FLYBACK LT3799 732-3191-ND - TRANSFORMER FLYBACK LT3799 732-2959-ND - TRANS OFFLINE600UH LT3799 LT4180 732-2898-ND - IND TOROID LT3799 NCL30000 750UH |
LT3799
OPERATION
R =
by the switch voltage clamp. Always check the switch
waveform with an oscilloscope to make sure the leakage
inductance voltage spike is below the breakdown voltage
of the MOSFET. A transient voltage suppressor and diode
are slower than the leakage inductance voltage spike,
therefore causing a higher voltage than calculated.
The secondary diode stress may be as much as
V OUT + 2 ? V IN /N PS due to the anode of the diode ringing
with the secondary leakage inductance. An RC snubber
in parallel with the diode eliminates this ringing, so that
the reverse voltage stress is limited to V OUT + V IN /N PS .
With a high N PS and output current greater than 3A, the
I RMS through the diode can become very high and a low
forward drop Schottky is recommended.
Discontinuous Mode Detection
The discontinuous mode detector uses AC-coupling to
detect the ringing on the third winding. A 10pF capacitor
with a 500Ω resistor in series is recommended in most
designs. Depending on the amount of leakage inductance
ringing, an additional current may be needed to prevent
false tripping from the leakage inductance ringing. A resis-
tor from INTV CC to the DCM pin adds this current. Up to
an additional 100μA of current may be needed in some
cases. The DCM pin is roughly 0.7V, therefore the resistor
value is selected using the following equation:
10V ? 0.7V
I
where I is equal to the additional current into the DCM pin.
switch proportional to the line voltage by using an internal
multiplier. A power factor of >0.97 is easily attainable for
most applications by following the design equations in this
datasheet. With proper design, LT3799 applications meet
IEC 6100-3-2 Class C harmonic standards.
Protection from Open LED and Shorted LED Faults
The LT3799 detects output overvoltage conditions by look-
ing at the voltage on the third winding. The third winding
voltage is proportional to the output voltage when the main
power switch is off and the secondary diode is conducting
current. Sensing the output voltage requires delivering
power to the output. Using the CT pin, the part turns off
switching when a overvoltage condition occurs and re-
checks to see if the overvoltage condition has cleared, as
described in “CT Pin and Faults” in the Operation section.
This greatly reduces the output current delivered to the
output but a Zener is required to dissipate 2% of the set
output current during an open LED condition. The Zener
diode’s voltage needs to be 10% higher than the output
voltage set by the resistor divider connected to the FB pin.
Multiple Zener diodes in series may be needed for higher
output power applications to keep the Zener’s temperature
within the specification.
During a shorted LED condition, the LT3799 operates at
the minimum operating frequency. In normal operation,
the third winding provides power to the IC, but the third
winding voltage is zero during a shorted LED condition.
This causes the part’s V IN UVLO to shutdown switching.
The part starts switching again when V IN has reached its
turn-on voltage.
Power Factor Correction/Harmonic Content
The LT3799 attains high power factor and low harmonic
content by making the peak current of the main power
3799fa
15
相关PDF资料 |
PDF描述 |
|---|---|
| GEA24DTMS | CONN EDGECARD 48POS R/A .125 SLD |
| AGL060V5-VQG100I | IC FPGA IGLOO 1.5V 100VQFP IND |
| SAA7706H/N210S,557 | IC DSP CAR RADIO 80QFP |
| SAA7706H/N107S,557 | IC DSP CAR RADIO 80QFP |
| MC78M12CDTRK | IC REG LDO 12V .5A DPAK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3799IMSE#PBF | 功能描述:IC LED DRIVER TRIAC DIM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| LT3799IMSE#PBF | 制造商:Linear Technology 功能描述:IC LED DRVR MSOP-16 制造商:Linear Technology 功能描述:IC, LED DRVR, MSOP-16 |
| LT3799IMSE#TRPBF | 功能描述:IC LED DRIVER TRIAC DIM 16-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3799IMSE-1#PBF | 功能描述:IC LED CTLR ISO ACT PFC 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3799IMSE-1#TRPBF | 功能描述:IC LED CTLR ISO ACT PFC 16MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。