- 您现在的位置：买卖IC网 > PDF目录14462 > LT3587EUD#PBF (Linear Technology)IC REG BOOST INV ADJ DL 20QFN PDF资料下载
参数资料
| 型号： | LT3587EUD#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/24页 |
| 文件大小： | 0K |
| 描述： | IC REG BOOST INV ADJ DL 20QFN |
| 标准包装： | 121 |
| 类型： | 升压（升压），反相 |
| 输出类型： | 可调式 |
| 输出数： | 2 |
| 输出电压： | 可调至 ±32V |
| 输入电压： | 2.5 V ~ 6 V |
| PWM 型： | 电流模式 |
| 频率 - 开关： | 1MHz |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 20-QFN 裸露焊盘（3x3） |
| 产品目录页面： | 1332 (CN2011-ZH PDF) |
LT3587
APPLICATIONS INFORMATION
Setting The Output Voltages and The Boost3 Output
Current
The LT3587 has a trimmed internal feedback resistor. A 1M
feedback resistor from each output pin to its corresponding
feedback pin sets the outputs to 15V for Boost1, –8V for the
inverter and 15V for Boost3. Note that only one resistor is
needed to set the output voltage for each channel. Set the
output voltages according to the following formulas:
R FB1 = ((V VOUT1 /1.22V) – 1) ? 88.5k
R FB2 = |V NEG |/8μA
R VFB3 = ((V VOUT3 /0.8V) – 1) ? 56.3k
As described in previous sections, Boost3 can be con?gured
as a boost current regulator. When con?gured as such, set
the output current according to the following formula:
R IFB3 = 200 ? (0.8V/I VOUT3 )
In order to maintain accuracy, use high precision resistors
when setting any of the channels output voltage and/or
the Boost3 output current (1% is recommended).
Connecting a capacitor from the EN/SS3 pin to ground
sets up a soft-start ramp for the Boost3 channel. As the
1μA current charges up the capacitor, the Boost3 regula-
tion loop is enabled when the EN/SS3 pin voltage goes
above 200mV. The V C3 node voltage follows the EN/SS3
voltage as it ramps up ensuring slow start-up on the
Boost3 channel. When the voltage at the EN/SS3 pin is
above 2V, the Boost3 regulation loop is free running with
full inductor current.
Start Sequencing
The LT3587 also has internal sequencing circuitry that
inhibits the inverter channel from operating until the feed-
back voltage of the Boost1 voltage (at the FB1 pin) reaches
about 1.1V (87% of the ?nal voltage). This ensures that
the Boost1 output voltage is near regulation before any
negative voltage is generated at the inverter output.
Figure 6 contrasts the start-up sequencing without any
soft-start capacitor, and with a 10nF soft-start capacitor.
Soft-Start
The LT3587 has two soft-start control pins: EN/SS1 and
EN/SS3. The EN/SS1 pin controls the soft-start for both
the Boost1 and the inverter, while the EN/SS3 pin controls
the soft-start for the Boost3. Each of these soft-start pins
is pulled up internally with a 1μA current source.
V EN/SS1
2V/DIV
I VIN
500mA/DIV
V VOUT1
10V/DIV
V NEG
10V/DIV
0V
0mA
0V
0V
Connecting a capacitor from the EN/SS1 pin to ground
programs a soft-start ramp for the Boost1 and the inverter
channels. Use an open-drain transistor to pull this pin low
to shut down both the Boost1 and the inverter. Turning off
this transistor allows the 1μA pull-up current to charge the
V EN/SS1
2V/DIV
400μs/DIV
3587 F06a
soft-start capacitor. When the voltage at the EN/SS1 pins
goes above 200mV, the regulation loops for Boost1 and
the inverter are enabled. The V C1 node voltage follows the
EN/SS1 voltage as it continues to ramp up to ensure slow
start-up on the Boost1 channel. The V C2 node follows the
ramp voltage minus 0.7V. This ensures that the inverter
I VIN
500mA/DIV
V VOUT1
10V/DIV
V NEG
10V/DIV
0mA
0V
0V
starts up after the Boost1, but still has a slow ramping
4ms/DIV
3587 F06b
output to avoid large start-up currents. The Boost1 and
the inverter regulation loops are free running with full
Figure 6. V EN/SS1 , V OUT1 , V NEG , I VIN with No Soft-Start
Capacitor, and with a 10nF Soft-Start Capacitor
inductor current when the voltage at the EN/SS1 pin is
above 2.5V.
3587fc
13
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BWB-EW-F4 | CONVERTER MOD DC/DC 95V 100W |
| 1130-392K-RC | CHOKE RF HI CURR 3900UH 10% RAD |
| 1130-391K-RC | CHOKE RF HI CURR 390UH 10% RAD |
| RCB34DHLR | CONN EDGECARD 68POS DIP .050 SLD |
| RCB34DHFT | CONN EDGECARD 68POS .050 SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3587EUD-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:High Voltage Monolithic Inverter and Dual Boost |
| LT3590 | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V Triple Step-Down LED Driver Programmable Temperature Protection |
| LT3590EDC#PBF | 制造商:Linear Technology 功能描述:IC LED DRIVER BULK MODE 48V 制造商:Linear Technology 功能描述:IC, LED DRIVER, BULK MODE, 48V |
| LT3590EDC#TRMPBF | 功能描述:IC LED DRIVER WHITE BCKLGT 6-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
| LT3590EDC#TRPBF | 功能描述:IC LED DRIVER WHITE BCKLGT 6-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:6,000 系列:- 恒定电流:- 恒定电压:- 拓扑:开路漏极，PWM 输出数:4 内部驱动器:是 类型 - 主要:LED 闪烁器 类型 - 次要:- 频率:400kHz 电源电压:2.3 V ~ 5.5 V 输出电压:- 安装类型:表面贴装 封装/外壳:8-VFDFN 裸露焊盘 供应商设备封装:8-HVSON 包装:带卷 (TR) 工作温度:-40°C ~ 85°C 其它名称:935286881118PCA9553TK/02-TPCA9553TK/02-T-ND |
发布紧急采购，3分钟左右您将得到回复。