- 您现在的位置：买卖IC网 > PDF目录13178 > FAN5026MTCX (Fairchild Semiconductor)IC CONTROLLER DDR 28TSSOP PDF资料下载
参数资料
| 型号： | FAN5026MTCX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 9/17页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR 28TSSOP |
| 产品变化通告： | Mold Compound Change 30/Nov/2007 |
| 标准包装： | 1 |
| 应用： | 控制器，DDR |
| 输入电压： | 3 V ~ 16 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1221 (CN2011-ZH PDF) |
| 其它名称： | FAN5026MTCXDKR |
Circuit Description
Overview
The FAN5026 is a multi-mode, dual-channel PWM
controller intended for graphic chipset, SDRAM, DDR
DRAM, or other low-voltage power applications in
modern notebook, desktop, and sub-notebook PCs.
The IC integrates control circuitry for two synchronous
buck converters. The output voltage of each controller
can be set in the range of 0.9V to 5.5V by an external
resistor divider.
The two synchronous buck converters can operate from
an unregulated DC source (such as a notebook
battery), with voltage ranging from 5.0V to 16V, or from
a regulated system rail of 3.3V to 5.0V. In either mode,
the IC is biased from a +5V source. The PWM
modulators use an average current-mode control with
input voltage feedforward for simplified feedback loop
compensation and improved line regulation. Both PWM
controllers have integrated feedback loop compensation
that reduces the external components needed.
The FAN5026 can be configured to operate as a
complete DDR solution. When the DDR pin is set HIGH,
the second channel provides the capability to track the
output voltage of the first channel. The PWM2 converter
is prevented from going into Hysteretic Mode if the DDR
pin is HIGH. In DDR Mode, a buffered reference voltage
(buffered voltage of the REF2 pin), required by DDR
memory chips, is provided by the PG2 pin.
Converter Modes and Synchronization
Table 3. Converter Modes and Synchronization
CLK
V D DQ
V TT
Figure 7. Noise-Susceptible 180° Phasing
for DDR1
In-phase operation is optimal to reduce inter-converter
interference when V IN is higher than 5V, (when V IN is
from a battery), as shown in Figure 8. Because the duty
cycle of PWM1 (generating V DDQ ) is short, the switching
point occurs far away from the decision point for the V TT
regulator, whose duty cycle is nominally 50%.
CLK
V DDQ
V TT
Figure 8. Optimal In-Phase Operation for DDR1
When V IN ≈ 5V, 180° phase-shifted operation can be
rejected for the reasons demonstrated in Figure 7.
In-phase operation with V IN ≈ 5V is even worse, since
the switch point of either converter occurs near the
switch point of the other converter, as seen in Figure 9.
In this case, as V IN is a little higher than 5V, it tends to
cause early termination of the V TT pulse width.
Mode
DDR1
DDR2
DUAL
V IN
Battery
+5V
ANY
VIN
Pin
V IN
R to
GND
V IN
DDR
Pin
HIGH
HIGH
LOW
PWM 2
w.r.t.
PWM1
IN PHASE
+90°
+180°
Conversely, the V TT switch point can cause early
termination of the V DDQ pulse width when V IN is slightly
lower than 5V.
CLK
V DDQ
When used as a dual converter, as shown in Figure 6,
out-of-phase operation with 180-degree phase shift
reduces input current ripple.
V TT
Figure 9.
Noise-Susceptible In-Phase Operation
for DDR2
For “two-step” conversion (where the V TT is converted
from V DDQ as in Figure 5) used in DDR Mode, the duty
cycle of the second converter is nominally 50% and the
optimal phasing depends on V IN . The objective is to
keep noise generated from the switching transition in
one converter from influencing the "decision" to switch
in the other converter.
When V IN is from the battery, it’s typically higher than
7.5V. As shown in Figure 7, 180° operation is
undesirable because the turn-on of the V DDQ converter
occurs very near the decision point of the V TT converter.
? 2005 Fairchild Semiconductor Corporation
FAN5026 ? Rev. 1.0.8
9
These problems are solved by delaying the second
converter’s clock by 90°, as shown in Figure 10. In this
way, all switching transitions in one converter take place
far away from the decision points of the other converter.
CLK
V DDQ
V TT
Figure 10. Optimal 90° Phasing for DDR2
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| ADP323ACPZ-R7 | IC REG LDO ADJ .2A 16LFCSP |
| VI-B3W-EU | CONVERTER MOD DC/DC 5.5V 200W |
| VI-23H-EX-F1 | CONVERTER MOD DC/DC 52V 75W |
| GCC28DREH-S734 | CONN EDGECARD 56POS .100 EYELET |
| RSM28DSUN | CONN EDGECARD 56POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5029 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:8-Bit Programmable 2- to 5-Phase Synchronous Buck Controller |
| FAN5029 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5029_07 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:8-Bit Programmable 2- to 5-Phase Synchronous Buck Controller |
| FAN5029_ABC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5029_ADC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。