- 您现在的位置：买卖IC网 > PDF目录13178 > FAN5026MTCX (Fairchild Semiconductor)IC CONTROLLER DDR 28TSSOP PDF资料下载
参数资料
| 型号： | FAN5026MTCX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 13/17页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER DDR 28TSSOP |
| 产品变化通告： | Mold Compound Change 30/Nov/2007 |
| 标准包装： | 1 |
| 应用： | 控制器，DDR |
| 输入电压： | 3 V ~ 16 V |
| 输出数： | 2 |
| 输出电压： | 0.9 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 1221 (CN2011-ZH PDF) |
| 其它名称： | FAN5026MTCXDKR |
Over-Voltage / Under-Voltage Protection
Should the V SNS voltage exceed 120% of V REF (0.9V)
due to an upper MOSFET failure or for other reasons,
the over-voltage protection comparator forces LDRV
HIGH. This action actively pulls down the output voltage
and, in the event of the upper MOSFET failure,
eventually blows the battery fuse. As soon as the output
voltage drops below the threshold, the OVP comparator
is disengaged.
This OVP scheme provides a ”soft” crowbar function,
Similarly, if an output short-circuit or severe load
transient causes the output to drop to less than 75% of
the regulation set point, the regulator shuts down.
Over-Temperature Protection
The chip incorporates an over-temperature protection
circuit that shuts the chip down if a die temperature of
about 150°C is reached. Normal operation is restored at
die temperature below 125°C with internal power-on
reset asserted, resulting in a full soft-start cycle.
which accommodates severe load transients and does
not invert the output voltage when activated —
a common problem for latched OVP schemes.
Design and Component Selection Guidelines
As an initial step, define the operating input voltage
range, output voltage, and minimum and maximum load
currents for the controller.
for this example, use:
V IN = 12 , V OUT = 2 . 5
Setting the Output Voltage
The internal reference voltage is 0.9V. The output is
divided down by a voltage divider to the VSEN pin (for
example, R5 and R6 in Figure 5). The output voltage
therefore is:
? I = 25 % ? 6 A = 1 . 5 A
f SW = 300 KHz
therefore:
L ≈ 4 . 4 H
(14)
(15)
0 . 9 V
R 6
=
V OUT ? 0 . 9 V
R 5
(10)
Output Capacitor Selection
The output capacitor serves two major functions in a
( 1 . 82 K ? ) V OUT ? 0 . 9 ) = 3 . 24 K ?
ESR <
To minimize noise pickup on this node, keep the
resistor to GND (R6) below 2K; for example, R6 at
1.82K ? . Then choose R5:
R 5 = (11)
0 . 9
For DDR applications converting from 3.3V to 2.5V or
other applications requiring high duty cycles, the duty
cycle clamp must be disabled by tying the converter’s
FPWM to GND. When converter’s FPWM is at GND,
the converter’s maximum duty cycle is greater than
90%. When using as a DDR converter with 3.3V input,
set up the converter for in-phase synchronization by
switching power supply. Along with the inductor, it filters
the sequence of pulses produced by the switcher and it
supplies the load transient currents. The requirements
are usually dictated by ESR, inductor ripple current ( ? I),
and the allowable ripple voltage ( ? V):
? V
(16)
? I
In addition, the capacitor’s ESR must be low enough to
allow the converter to stay in regulation during a load
step. The ripple voltage due to ESR for the converter in
Figure 6 is 120mV PP . Some additional ripple appears
due to the capacitance value itself:
tying the VIN pin to +5V.
Output Inductor Selection
? V =
? I
C OUT × 8 × f SW
(17)
? I = 2 × 1 MIN =
(12)
The minimum practical output inductor value keeps the
inductor current just on the boundary of continuous
conduction at some minimum load. Industry standard
practice is to choose the minimum current somewhere
from 15% to 35% of the nominal current. At light load,
the controller can automatically switch to Hysteretic
Mode to sustain high efficiency. The following equations
select the proper value of the output filter inductor:
? V
OUT
ESR
where ? I is the inductor ripple current and ? V OUT is the
maximum ripple allowed:
which is only about 1.5mV for the converter in Figure 6
and can be ignored.
The capacitor must also be rated to withstand the RMS
current, which is approximately 0.3 X ( ? I), or about
400mA, for the converter in Figure 6. High-frequency
decoupling capacitors should be placed as close to the
loads as physically possible .
Input Capacitor Selection
The input capacitor should be selected by its ripple
current rating.
L =
V IN ? V OUT
f SW × ? I
×
V OUT
V IN
(13)
? 2005 Fairchild Semiconductor Corporation
FAN5026 ? Rev. 1.0.8
13
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| ADP323ACPZ-R7 | IC REG LDO ADJ .2A 16LFCSP |
| VI-B3W-EU | CONVERTER MOD DC/DC 5.5V 200W |
| VI-23H-EX-F1 | CONVERTER MOD DC/DC 52V 75W |
| GCC28DREH-S734 | CONN EDGECARD 56POS .100 EYELET |
| RSM28DSUN | CONN EDGECARD 56POS DIP .156 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FAN5029 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:8-Bit Programmable 2- to 5-Phase Synchronous Buck Controller |
| FAN5029 WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5029_07 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:8-Bit Programmable 2- to 5-Phase Synchronous Buck Controller |
| FAN5029_ABC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5029_ADC3086B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。