参数资料
| 型号： | AD5749ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 28/28页 |
| 文件大小： | 0K |
| 描述： | IC CURRENT OUT DVR 32-LFCSP |
| 标准包装： | 1 |
| 放大器类型： | 仪表 |
| 电路数： | 1 |
| 电流 - 电源： | 5.2mA |
| 电流 - 输出 / 通道： | 24mA |
| 电压 - 电源，单路/双路(±)： | 10.8 V ~ 55 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页
Data Sheet
AD5749
Rev. B | Page 9 of 28
Pin No.
Mnemonic
Description
12, 13
REXT2, REXT1
A 15 k external current setting resistor can be connected between the REXT1 and REXT2 pins to
improve the IOUT temperature drift performance.
14
VREF
Buffered Reference Input.
15
VIN
Buffered Analog Input (0 V to 4.096 V).
16
GND
Ground Connection.
17
AVDD
Positive Analog Supply.
18
IOUT
Current Output.
19, 20, 23, 24
DNC
Do not connect to these pins.
21, 22
GND
Ground Connection.
25, 26, 27, 28
NC
No Connect. Can be tied to GND.
29
HW SELECT
This part is used to configure the part to hardware or software mode.
HW SELECT = 0 selects software control.
HW SELECT = 1 selects hardware control.
30
RESET
In software mode, this pin resets the part to its power-on state. Active low.
In hardware mode, there is no reset. If using the part in hardware mode, the RESET pin should be tied high.
31
FAULT/TEMP
Fault Alert (FAULT). In software mode, this pin acts as a general fault alert pin. It is asserted low when an
open-circuit, overtemperature error, or PEC interface error is detected. This pin is an open-drain output
and must be connected to a pull-up resistor.
Overtemperature Fault (TEMP). In hardware mode, this pin acts as an overtemperature fault pin. It is
asserted low when an overtemperature error is detected. This pin is an open-drain output and must be
connected to a pull-up resistor.
32
NC/IFAULT
No Connect (NC). In software mode, this pin is a no connect. Instead, tie this pin to GND.
Open-Circuit Fault Alert (IFAULT). In hardware mode, this pin acts as an open-circuit fault alert pin. It is
asserted low when an open-circuit error is detected. This pin is an open-drain output and must be
connected to a pull-up resistor.
33 (EPAD)
EPAD
The exposed paddle is tied to GND.
相关PDF资料 |
PDF描述 |
|---|---|
| AD5750-1ACPZ-REEL7 | IC CURR/VOLT OUT DVR 32LFCSP |
| AD5750-2BCPZ-RL7 | IC CURR/VOLT OUT DRVR 32LFCSP |
| AD5751ACPZ-REEL7 | IC I/V OUTPUT DRIVER 60V 32LFCSP |
| AD582SD | IC AMP SAMPLE HOLD 25MA 14CDIP |
| AD585SQ | IC AMP SAMPLE HOLD 50MA 14CDIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5749ACPZ-RL7 | 功能描述:IC CURRENT OUT DVR 32-LFCSP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:LinCMOS™ 放大器类型:通用 电路数:4 输出类型:- 转换速率:0.05 V/µs 增益带宽积:110kHz -3db带宽:- 电流 - 输入偏压:0.7pA 电压 - 输入偏移:210µV 电流 - 电源:57µA 电流 - 输出 / 通道:30mA 电压 - 电源，单路/双路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOIC 包装:管件 产品目录页面:865 (CN2011-ZH PDF) 其它名称:296-1834296-1834-5 |
| AD574A | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 12-Bit A/D Converter |
| AD574AJ | 制造商:AD 制造商全称:Analog Devices 功能描述:Complete 12-Bit A/D Converter |
| AD574AJD | 功能描述:IC ADC 12BIT W/REF 28-CDIP RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。