- 您现在的位置：买卖IC网 > Datasheet目录610 > 9-1478239-0 (TE Connectivity)TOOL HAND CRIMPING TYPE N Datasheet资料下载
参数资料
| 型号： | 9-1478239-0 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/3页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPING TYPE N |
| 标准包装： | 1 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - N |
| 特点： | 侧面插入，棘齿 |
408-8695
or abnormal wear is evident, the dies must be
replaced. Refer to Section 7, PARTS REPLACEMENT.
5.2. Measuring Die Opening
If the crimp cannot be made to conform to the
dimensions provided in the appropriate product
application specification, the tool and/or dies are
defective and must be replaced.
The die assembly will perform correctly as long as:
? the product specified is correct for the application;
? the specific die assembly is used;
? the die assembly has been measured to ensure
NOTE
i
Other hex crimp dies are used to crimp
GREENPAR connectors. The hand tool frame may
be used, however, the ratchet adjustment wheel
may require adjustment to achieve acceptable
crimp height.
crimping operation, it must be replaced with a new
one.
that the openings are correct; and
? the tool has been adjusted correctly.
Figure 5 provides information on die opening sizes.
6. DAMAGED CONTACTS AND FERRULES
CAUTION Damaged contacts or ferrules may not be used. If a
center contact or ferrule is damaged during the
!
7. PARTS REPLACEMENT
If the dies are damaged or worn excessively, they
must be replaced. Order replacement dies through
your Tyco Electronics Representative, or call 1-800-
526-5142, or send a facsimile of your purchase order
to 1-717-986-7605, or write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
8. REVISION SUMMARY
2.60±0.10
.102±.004]
10.20±0.10
[.402±.004]
Since the previous release of these instructions, the
TE logo ws applied.
Figure 5
5.3. Ratchet Adjustment
The tool frame assembly ratchet mechanism features
an adjustment wheel with nine settings. The
adjustment wheel controls the amount of handle
pressure exerted on the tool jaws and crimping dies
during crimping. If the crimp is not acceptable, adjust
the ratchet as follows:
1. If the crimp is too loose, turn the wheel to a
higher notch. If the crimp is too tight, move the
wheel to a lower notch.
2. Replace and tighten the screw at the ratchet
adjustment wheel.
Rev B
3 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 9-1478240-0 | TOOL HAND CRIMPING SDE PEW 12 |
| 90017-3 | ASSY SAHT |
| 90026 | TOOL SHORT HANDLE 24-22AWG CRIMP |
| 90045 | DAHT F CRIMP 14-18 |
| 90050-1 | DAHT TAPER PIN 16-20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9-1478240-0 | 功能描述:折皱器 SDE PEW 12 HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 9-1478242-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG58-RG59-URM70 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478243-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF 1/2-BEL8281 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478245-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF1/7 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478246-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG9-RG214-URM90 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。