- 您现在的位置：买卖IC网 > Datasheet目录610 > 9-1478239-0 (TE Connectivity)TOOL HAND CRIMPING TYPE N Datasheet资料下载
参数资料
| 型号： | 9-1478239-0 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMPING TYPE N |
| 标准包装： | 1 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - N |
| 特点： | 侧面插入，棘齿 |
408-8695
3. Thread the retaining screws into the holes and
carefully close the tool handles. Tighten the
screws with the appropriate hex wrench.
4. CRIMPING PROCEDURE
See Figure 2.
4.1. Center Contact
1. Prepare the connector and the cable according
to the instructions packaged with the connector.
2. Slide the center contact onto the center
conductor of the cable; then insert the contact
assembly into the center contact crimp section of
the die.
2. Slide the ferrule forward over the braid until the
ferrule butts against the shoulder on the
connector body.
Flange on End of Center
Contact Butts Against Die
Flange on End
of Contact
Insert Center
Contact Into
Partially Closed
Crimping Dies
Center Contact
Slipped Over
Center Conductor
Crimping Die
Figure 3
3. Place the ferrule on the anvil of the die
assembly so that the shoulder on the connector
body is butted against the die. See Figure 4.
4. Holding the assembly in place, close the tool
handles until the ratchet releases.
Ferrule
(Ref)
Figure 2
Crimping Die (Ref)
Shoulder on
Connector Body
Butts Against Die
NOTE
i
Make sure that the flange on the end of the center
contact butts against the crimping die. See
Figure 3.
3. Crimp the center contact by holding the cable
in place; then close the tool handles until the
ratchet releases.
Typical RF
Connector (Ref)
Ferrule on Anvil of
Crimping Dies
A. Ferrule
1. Insert the crimped center contact into the
connector body until the cable dielectric butts
against the dielectric inside of the connector
body. The flared braid will then fit around the
support sleeve of the connector body.
Rev B
Figure 4
5. INSPECTION
5.1. Visual Inspection
Inspection of the crimping dies should be made on a
regular basis to ensure that they have not become
worn or damaged. Inspect the crimp sections for
flattened, chipped, worn, or broken areas. If damage
2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 9-1478240-0 | TOOL HAND CRIMPING SDE PEW 12 |
| 90017-3 | ASSY SAHT |
| 90026 | TOOL SHORT HANDLE 24-22AWG CRIMP |
| 90045 | DAHT F CRIMP 14-18 |
| 90050-1 | DAHT TAPER PIN 16-20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 9-1478240-0 | 功能描述:折皱器 SDE PEW 12 HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 9-1478242-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG58-RG59-URM70 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478243-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF 1/2-BEL8281 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478245-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE PSF1/7 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 9-1478246-0 | 功能描述:冲压机与冲模 PRO-C HEX DIE RG9-RG214-URM90 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。