- 您现在的位置：买卖IC网 > PDF目录19196 > 58546-1 (TE Connectivity)TOOL CRIMP UNINSUL TERM 10-22AWG PDF资料下载
参数资料
| 型号： | 58546-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP UNINSUL TERM 10-22AWG |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Solistrand |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头，10-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 384 (CN2011-ZH PDF) |
| 配用： | 8-330368-1-ND - CONN BUTT SPLICE UNINS 14-16AWG 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 8-31819-6-ND - CONN BUTT SPLICE UNINS 14-16AWG 8-330369-2-ND - CONN SPLICE SOLIS BUTT 12-10AWG 51893-ND - CONN SPLICE SOLISTRAND BUTT 2-321801-3-ND - CONN SPLICE BUTT 22-16AWG SOLIS 8-32151-1-ND - SPLICE,SOLIS BUTT 12-10AWG 326745-ND - CONN SPLICE BUTT 22-20AWG SOLIS 328592-ND - CONN SPLICE BUTT 18-16AWG STRAP 8-330367-1-ND - CONN SPLICE BUTT 22-16AWG TIN 更多... |
| 其它名称： | A9812 |
The GO element must pass completely through the
crimping chamber. See Figure 5.
4. Align the NO–GO element and try to insert it
straight into the same crimping chamber. The
NO–GO element may start entry, but must not
pass completely through the crimping chamber.
See Figure 5.
Figure 6
The frame assembly ratchet mechanism features an
adjustment wheel with numbered settings. If the dies
do not bottom, adjust the ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
2. With a screwdriver, adjust the ratchet wheel
from the opposite side of the frame.
3. Observe the ratchet adjustment wheel. If the
dies do not bottom, rotate the adjustment wheel
COUNTERCLOCKWISE to a higher–numbered
setting.
4. Replace the lockscrew.
Ensure that the tool and dies are clean by wiping
them with a clean, soft cloth. Remove any debris with
a clean, soft brush. Do not use objects that could
damage the tool. When not in use, keep handles
Figure 5
closed to prevent objects from becoming lodged in
the crimping dies, and store in a clean, dry area.
If the crimping chamber conforms to the gage
inspection, the tool is considered dimensionally
correct, and should be lubricated with a THIN coat of
any good SAE 20 motor oil. If not, the tool must be
returned to Tyco Electronics for further evaluation and
repair. Refer to Section 8, REPLACEMENT.
For additional information regarding the use of a plug
gage, refer to Instruction Sheet 408–7424.
The die assembly should be inspected on a regular
basis to ensure that they have not become worn or
damaged. Inspect the crimping chambers for
flattened, chipped, worn, or broken areas. If damage
or abnormal wear is evident, the tool or dies must be
replaced. See Section 8, REPLACEMENT.
相关PDF资料 |
PDF描述 |
|---|---|
| 210-4ESD | SWITCH EXTENDED ACTUATOR 4 SEC |
| 210-4MSD | SWITCH RAISED ACTUATOR 4 SEC |
| 210-4LPSD | SWITCH SPST 4 SEC STRAIGHT TERM |
| 90758-1 | PROCRIMPER III W/DIE 22-26 AWG |
| YRS-859 | CRIMP TOOL STRIP FEED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58546-2 | 功能描述:折皱器 SOLIS 22-10AWG W/DIE AS (-1) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58547 | 制造商:Brady Corporation 功能描述: |
| 58548-1 | 功能描述:折皱器 PRO-CRIMPER W/DIE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58548-2 | 功能描述:冲压机与冲模 DIE ASSEMBLY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 585-48-3 | 制造商:Fox Electronics 功能描述:SMD,3.2X2.5,HCMOS OSC,-40+85,100PPM,3.3V,48.0000 MHZ - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。