- 您现在的位置：买卖IC网 > PDF目录19196 > 58546-1 (TE Connectivity)TOOL CRIMP UNINSUL TERM 10-22AWG PDF资料下载
参数资料
| 型号： | 58546-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMP UNINSUL TERM 10-22AWG |
| 特色产品： | SOLISTRAND?, Budget, and DIAMOND GRIP? Terminals and Splices |
| 标准包装： | 1 |
| 系列： | Pro-Crimper III, Solistrand |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 接头，10-22 AWG |
| 特点： | 侧面插入，棘齿 |
| 产品目录页面： | 384 (CN2011-ZH PDF) |
| 配用： | 8-330368-1-ND - CONN BUTT SPLICE UNINS 14-16AWG 328600-ND - CONN BUTT SPLICE UNINS 10-12AWG 8-31819-6-ND - CONN BUTT SPLICE UNINS 14-16AWG 8-330369-2-ND - CONN SPLICE SOLIS BUTT 12-10AWG 51893-ND - CONN SPLICE SOLISTRAND BUTT 2-321801-3-ND - CONN SPLICE BUTT 22-16AWG SOLIS 8-32151-1-ND - SPLICE,SOLIS BUTT 12-10AWG 326745-ND - CONN SPLICE BUTT 22-20AWG SOLIS 328592-ND - CONN SPLICE BUTT 18-16AWG STRAP 8-330367-1-ND - CONN SPLICE BUTT 22-16AWG TIN 更多... |
| 其它名称： | A9812 |
1. Hold tool so that the back (wire side) is facing
you. Squeeze tool handles together until the
ratchet releases, then allow them to open fully.
2. Center the splice wire barrel on the anvil of the
upper die as shown in Figure 3. If visible, be sure
to place the brazed seam on the splice toward the
indenter.
Figure 3
3. Hold the wire barrel in place and squeeze the
tool handles together until ratchet engages
sufficiently to hold the splice in position. Do NOT
deform the insulation barrel or wire barrel.
4. Insert stripped wire into the wire barrel, making
sure that the insulation does not enter the wire
barrel. See Figure 3.
5. Holding wire in place, squeeze tool handles
together until ratchet releases. Allow tool handles
to open, then remove crimped splice.
6. To crimp the other half of a splice, reposition the
uncrimped wire barrel in the crimping chamber, and
repeat the crimping procedure.
7. Inspect the crimped splice according to
Figure 4. Check the crimp height as described in
Section 5. If necessary, adjust the shut height as
described in Section 6.
Figure 4
This inspection requires the use of plug gages
conforming to the dimensions provided in Figure 5.
Tyco Electronics does not manufacture or market
these gages. To gage the crimping chamber, proceed
as follows:
1. Remove traces of oil or dirt from the crimping
chamber and plug gage.
2. Close the tool handles until the dies have
bottomed. Do NOT force dies beyond initial
contact.
3. Align the GO element with the crimping
chamber. Push element straight into the crimping
chamber without using force.
相关PDF资料 |
PDF描述 |
|---|---|
| 210-4ESD | SWITCH EXTENDED ACTUATOR 4 SEC |
| 210-4MSD | SWITCH RAISED ACTUATOR 4 SEC |
| 210-4LPSD | SWITCH SPST 4 SEC STRAIGHT TERM |
| 90758-1 | PROCRIMPER III W/DIE 22-26 AWG |
| YRS-859 | CRIMP TOOL STRIP FEED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58546-2 | 功能描述:折皱器 SOLIS 22-10AWG W/DIE AS (-1) RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58547 | 制造商:Brady Corporation 功能描述: |
| 58548-1 | 功能描述:折皱器 PRO-CRIMPER W/DIE RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 58548-2 | 功能描述:冲压机与冲模 DIE ASSEMBLY RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 585-48-3 | 制造商:Fox Electronics 功能描述:SMD,3.2X2.5,HCMOS OSC,-40+85,100PPM,3.3V,48.0000 MHZ - Cut Tape Product |
发布紧急采购，3分钟左右您将得到回复。