- 您现在的位置：买卖IC网 > PDF目录21898 > 4307-52 (Peregrine Semiconductor)IC DSA 5BIT 75 OHM 20-QFN PDF资料下载
参数资料
| 型号： | 4307-52 |
| 厂商： | Peregrine Semiconductor |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC DSA 5BIT 75 OHM 20-QFN |
| 标准包装： | 1 |
| 系列： | UltraCMOS™ |
| 衰减值： | 15.5dB |
| 容差： | ±0.15dB |
| 频率范围： | 0 ~ 2GHz |
| 阻抗： | 75 欧姆 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 其它名称： | 1046-1034-6 |
PE4307
Product Specification
Programming Options
Parallel/Serial Selection
Either a parallel or serial interface can be used to
control the PE4307. The P/S bit provides this
selection, with P/S = LOW selecting the parallel
interface and P/S = HIGH selecting the serial
interface.
Parallel / Direct Mode Interface
The parallel interface consists of five CMOS-
compatible control lines that select the desired
attenuation state, as shown in Table 5 .
The parallel interface timing requirements are
defined by Figure 19 (Parallel Interface Timing
Diagram), Table 9 (Parallel Interface AC
Characteristics), and switching speed ( Table 1 ).
For latched parallel programming, the Latch Enable
(LE) should be held LOW while changing attenuation
state control values, then pulse LE HIGH to LOW
(per Figure 19 ) to latch new attenuation state into
device.
For direct parallel programming, the Latch Enable
(LE) line should be pulled HIGH. Changing
attenuation state control values will change device
state to new attenuation. Direct Mode is ideal for
manual control of the device (using hardwire,
switches, or jumpers).
serially entered into the shift register, a process that
is independent of the state of the LE input.
The LE input controls the latch. When LE is HIGH,
the latch is transparent and the contents of the serial
shift register control the attenuator. When LE is
brought LOW, data in the shift register is latched.
The shift register should be loaded while LE is held
LOW to prevent the attenuator value from changing
as data is entered. The LE input should then be
toggled HIGH and brought LOW again, latching the
new data. The start bit (B5) of the data should
always be low to prevent an unknown state in the
device. The timing for this operation is defined by
Figure 18 (Serial Interface Timing Diagram) and
Table 8 (Serial Interface AC Characteristics).
Power-up Control Settings
The PE4307 always assumes a specifiable
attenuation setting on power-up. This feature exists
for both the Serial and Parallel modes of operation,
and allows a known attenuation state to be
established before an initial serial or parallel control
word is provided.
When the attenuator powers up in Serial mode
(P/S = 1), the five control bits are set to whatever
data is present on the five parallel data inputs (C0.5
to C8). This allows any one of the 32 attenuation
settings to be specified as the power-up state.
Table 5. Truth Table
P/S C8 C4 C2
0 0 0 0
0 0 0 0
C1
0
0
C0.5
0
1
Attenuation
State
Reference Loss
0.5 dB
When the attenuator powers up in Parallel mode
(P/S = 0) with LE = 0, the control bits are
automatically set to one of two possible values.
These two values are selected by the power-up
control bit, PUP2, as shown in Table 6 (Power-Up
0
0
0
0
0
0
0
0
1
1
0
0
1
0
1
0
1
0
0
1
1
0
0
0
1
0
0
0
0
1
1 dB
2 dB
4 dB
8 dB
15.5 dB
Truth Table, Parallel Mode).
Table 6. Power-Up Truth Table, Parallel
Interface Mode
Note: Not all 32 possible combinations of C0.5-C8 are shown in table
Serial Interface
P/S
0
0
LE
0
0
PUP2
0
1
Attenuation State
Reference Loss
8 dB
X
The PE4307’s serial interface is a 6-bit serial-in,
parallel-out shift register buffered by a transparent
latch. The latch is controlled by three CMOS-
compatible signals: Data, Clock, and Latch Enable
(LE). The Data and Clock inputs allow data to be
Document No. 70-0161-05 │ www.psemi.com
0 1 Defined by C0.5-C8
Note: Power up with LE=1 provides normal parallel operation with C0.5-C8,
and PUP2 is not active
?2003-2013 Peregrine Semiconductor Corp. All rights reserved.
Page 7 of 11
Logo updated under non-rev change. Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| DMS-20PC-1-DCM-B-C | DPM LED 8-50VDC 3.5DIGIT BLUE |
| DMS-30PC-2-RL-C | DPM LED MINI 20VDC 3.5DIG LP RED |
| ELSW-F91G3-0LPNM-DG1G3 | LED SHWO 3W HI PWR GREEN SMD |
| 4305-52 | IC DSA 5BIT 50 OHM 20-QFN |
| DMS-30PC-3-RL-C | DPM LED MINI 200V 3.5DIG LP RED |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4307-54 | 功能描述:RF Attenuator 15.5dB @ 1MHz ~ 2GHz ±0.15dB 1MHz ~ 2GHz 75 Ohm 20-VFQFN Exposed Pad 制造商:peregrine semiconductor 系列:- 零件状态:过期 衰减值:15.5dB @ 1MHz ~ 2GHz 容差:±0.15dB 频率范围:1MHz ~ 2GHz 功率（W）:- 阻抗:75 欧姆 封装/外壳:20-VFQFN 裸露焊盘 标准包装:1 |
| 4307-565F | 功能描述:固定电感器 5.6mH, 1 %, 56mA Molded Shielded Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 4307-565G | 功能描述:固定电感器 5.6mH, 2 %, 56mA Molded Shielded Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 4307-565H | 功能描述:固定电感器 5.6mH, 3 %, 56mA Molded Shielded Coil RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm |
| 4307-565H TR 2500 | 制造商:API Delevan 功能描述:INDUCTOR SHIELDED RF 5600 UH 3% |
发布紧急采购，3分钟左右您将得到回复。