- 您现在的位置：买卖IC网 > PDF目录21898 > 4305-52 (Peregrine Semiconductor)IC DSA 5BIT 50 OHM 20-QFN PDF资料下载
参数资料
| 型号： | 4305-52 |
| 厂商： | Peregrine Semiconductor |
| 文件页数： | 6/11页 |
| 文件大小： | 0K |
| 描述： | IC DSA 5BIT 50 OHM 20-QFN |
| 标准包装： | 1 |
| 系列： | UltraCMOS™ |
| 衰减值： | 15.5dB |
| 容差： | ±0.25dB |
| 频率范围： | 0 ~ 4GHz |
| 阻抗： | 50 欧姆 |
| 封装/外壳： | 20-WFQFN 裸露焊盘 |
| 其它名称： | 1046-1032-6 |
PE4305
Product Specification
Programming Options
Parallel/Serial Selection
Either a parallel or serial interface can be used to
control the PE4305. The P/S bit provides this
selection, with P/S=LOW selecting the parallel
interface and P/S=HIGH selecting the serial
interface.
Parallel / Direct Mode Interface
The parallel interface consists of five CMOS-
compatible control lines that select the desired
attenuation state, as shown in Table 5.
The parallel interface timing requirements are
defined by Figure 18 (Parallel Interface Timing
Diagram), Table 9 (Parallel Interface AC
Characteristics), and switching speed (Table 1).
For parallel programming the Latch Enable (LE)
should be held LOW while changing attenuation
state control values, then pulse LE HIGH to LOW
(per Figure 18) to latch new attenuation state into
device.
For direct programming, the Latch Enable (LE) line
should be pulled HIGH. Changing attenuation state
control values will change device state to new
attenuation. Direct Mode is ideal for manual control
of the device (using hardwire, switches, or jumpers).
Table 5. Truth Table
serially entered into the shift register, a process that
is independent of the state of the LE input.
The LE input controls the latch. When LE is HIGH,
the latch is transparent and the contents of the serial
shift register control the attenuator. When LE is
brought LOW, data in the shift register is latched.
The shift register should be loaded while LE is held
LOW to prevent the attenuator value from changing
as data is entered. The LE input should then be
toggled HIGH and brought LOW again, latching the
new data. The start bit (B5) of the data should
always be low to prevent an unknown state in the
device. The timing for this operation is defined by
Figure 17 (Serial Interface Timing Diagram) and
Table 8 (Serial Interface AC Characteristics).
Power-up Control Settings
The PE4305 always assumes a specifiable
attenuation setting on power-up. This feature exists
for both the Serial and Parallel modes of operation,
and allows a known attenuation state to be
established before an initial serial or parallel control
word is provided.
When the attenuator powers up in Serial mode (P/
S=1), the five control bits are set to whatever data is
present on the five parallel data inputs (C0.5 to C8).
This allows any one of the 32 attenuation settings to
be specified as the power-up state.
When the attenuator powers up in Parallel mode (P/
P/S
0
0
0
0
0
0
C8
0
0
0
0
0
1
C4
0
0
0
0
1
0
C2
0
0
0
1
0
0
C1
0
0
1
0
0
0
C0.5
0
1
0
0
0
0
Attenuation
State
Reference Loss
0.5 dB
1 dB
2 dB
4 dB
8 dB
S=0) with LE=0, the control bits are automatically set
to one of two possible values. These two values are
selected by the power-up control bit, PUP2, as
shown in Table 6 (Power-Up Truth Table, Parallel
Mode).
Table 6. Power-Up Truth Table, Parallel
Interface Mode
0
1
1
1
1
1
15.5 dB
P/S
LE
PUP2
Attenuation State
Note: Not all 32 possible combinations of C0.5-C8 are shown in table
Serial Interface
The PE4305’s serial interface is a 6-bit serial-in,
0
0
0
0
0
1
0
1
X
Reference Loss
8 dB
Defined by C0.5-C8
parallel-out shift register buffered by a transparent
latch. The latch is controlled by three CMOS-
compatible signals: Data, Clock, and Latch Enable
(LE). The Data and Clock inputs allow data to be
?2003-2008 Peregrine Semiconductor Corp. All rights reserved.
Note: Power up with LE=1 provides normal parallel operation with
C0.5-C8, and PUP2 is not active
Document No. 70-0159-06 │ UltraCMOS? RFIC Solutions
Page 6 of 11
Peregrine products are protected under one or more of the following U.S. Patents: http://patents.psemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| DMS-30PC-3-RL-C | DPM LED MINI 200V 3.5DIG LP RED |
| ELSH-F91Y3-0LPNM-BA3A5 | LED SHUEN 3W HI PWR YLW SMD |
| DMS-30PC-1-RL-C | DPM LED MINI 2VDC 3.5DIG LP RED |
| PE43404MLI-Z | IC RF DSA 4-BIT 75 OHM 20-QFN |
| DK703 | LCD DPM +5V 2V 4.5 DIGIT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 430-5570-001X | 制造商:DIALIGHT 制造商全称:Dialight Corporation 功能描述:LED Signal Modules and Pedestrian Signals |
| 430557-501 | 制造商:LAIRD TECHNOLOGIES - ENGINEERED THERMAL SOLUTIONS 功能描述:PELTR HOT12,65,F2A,1312,GG,W2.25 制造商:Laird Technologies Inc 功能描述:PELTR HOT12,65,F2A,1312,GG,W2.25 |
| 4305-680LF | 功能描述:电磁干扰直通滤波器 5pF 300Volts -55C + 125C RoHS:否 制造商:Tusonix 电容:0.027 uF 电压额定值:50 V 电路类型: 最大直流电流: 最大直流电阻: 工作温度范围:- 55 C to + 125 C 系列:4403 螺纹大小:4-40 UNC-2A |
| 430-5682-01-00-00 | 制造商:Wearnes Cambion 功能描述:POSITIONER FOR THE CRIMP TOOL UNIQUE FOR CRIMPING P/N 450- |
| 4-305688-5 | 制造商:TE Connectivity 功能描述:INDENTER - Bulk |
发布紧急采购，3分钟左右您将得到回复。