- 您现在的位置：买卖IC网 > PDF目录192295 > S25FL064A0LNAI00 (SPANSION LLC) 64M X 1 FLASH 3V PROM, PDSO16 PDF资料下载
参数资料
| 型号： | S25FL064A0LNAI00 |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 64M X 1 FLASH 3V PROM, PDSO16 |
| 封装： | 0.300 INCH, PLASTIC, MS-013AA, SOP-16 |
| 文件页数： | 5/36页 |
| 文件大小： | 1495K |
| 代理商： | S25FL064A0LNAI00 |
第1页第2页第3页第4页当前第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
14
S25FL064A
S25FL064A_00_C3 June 29, 2007
Da ta
Sh e e t
7.7
Hold Mode (HOLD#)
The Hold input (HOLD#) stops any serial communication with the device, but does not terminate any Write
Status Register, program or erase operation that is currently in progress.
The Hold mode starts on the falling edge of HOLD# if SCK is also low (see Figure 7.1, standard use). If the
falling edge of HOLD# does not occur while SCK is low, the Hold mode begins after the next falling edge of
SCK (non-standard use).
The Hold mode ends on the rising edge of HOLD# signal (standard use) if SCK is also low. If the rising edge
of HOLD# does not occur while SCK is low, the Hold mode ends on the next falling edge of CLK (non-
standard use) See Figure 7.1.
The SO output is high impedance, and the SI and SCK inputs are ignored (don’t care) for the duration of the
Hold mode.
CS# must remain low for the entire duration of the Hold mode to ensure that the device internal logic remains
unchanged. If CS# goes high while the device is in the Hold mode, the internal logic is reset. To prevent the
device from reverting to the Hold mode when device communication is resumed, HOLD# must be held high,
followed by driving CS# low.
Figure 7.1 Hold Mode Operation
8.
Sector Address Table
Table 8.1 shows the size of the memory array, sectors, and pages. The device uses pages to cache the
program data before the data is programmed into the memory array. Each page or byte can be individually
programmed (bits are changed from 1 to 0). The data is erased (bits are changed from 0 to 1) on a sector- or
device-wide basis using the SE or BE commands. Table 8.2 on page 15 shows the starting and ending
address for each sector. The complete set of sectors comprises the memory array of the Flash device.
SCK
HOLD#
Hold
Condition
(standard use)
Hold
Condition
(non-standard use)
Table 8.1 S25FL064A Device Organization
Each Device has
Each Sector has
Each Page has
8,388,608
65,536
256
bytes
32,768
256
—
pages
128
—
sectors
相关PDF资料 |
PDF描述 |
|---|---|
| S2684-254 | PHOTO DIODE |
| S2815S | 1-OUTPUT 10 W DC-DC REG PWR SUPPLY MODULE |
| S29AL032D70BAE000 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D70BAE002 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
| S29AL032D90TFI042 | 32 Megabit CMOS 3.0 Volt-only Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| S25FL064K | 制造商:SPANSION 制造商全称:SPANSION 功能描述:64-Mbit CMOS 3.0 Volt Flash Memory with 80-MHz SPI (Serial Peripheral Interface) Multi I/O Bus |
| S25FL064K0SMFI010 | 功能描述:闪存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| S25FL064K0SMFI011 | 功能描述:闪存 IC 64MBIT CMOS 3V FL MEMORY 80-MHZ SPI RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel |
| S25FL064K0SMFI013 | 制造商:Spansion 功能描述:FLASH SERL-SPI 3V/3.3V 64MBIT - Bulk |
| S25FL064LABBHI020 | 功能描述:IC FLASH NOR 24FBGA 制造商:cypress semiconductor corp 系列:FL-L 包装:托盘 零件状态:在售 存储器类型:非易失 存储器格式:闪存 技术:FLASH - NOR 存储容量:64Mb （8M x 8） 时钟频率:108MHz 写周期时间 - 字，页:- 存储器接口:SPI - 四 I/O， QPI 电压 - 电源:2.7 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:24-TBGA 供应商器件封装:24-BGA（6x8） 标准包装:338 |
发布紧急采购，3分钟左右您将得到回复。