参数资料
| 型号： | LT6204IS#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP R-R INOUT QUAD LP14SOIC |
| 标准包装： | 55 |
| 放大器类型： | 通用 |
| 电路数： | 4 |
| 输出类型： | 满摆幅 |
| 转换速率： | 25 V/µs |
| 增益带宽积： | 100MHz |
| 电流 - 输入偏压： | 3.8µA |
| 电压 - 输入偏移： | 2600µV |
| 电流 - 电源： | 2.8mA |
| 电流 - 输出 / 通道： | 40mA |
| 电压 - 电源，单路/双路(±)： | 2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SO |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT6202/LT6203/LT6204
19
620234fd
APPLICATIONS INFORMATION
Input Protection
There are back-to-back diodes, D1 and D2, across the
+ and – inputs of these amplifiers to limit the differential
input voltage to ±0.7V. The inputs of the LT6202/LT6203/
LT6304 do not have internal resistors in series with the
input transistors. This technique is often used to protect
the input devices from over voltage that causes excessive
currents to flow. The addition of these resistors would
significantly degrade the low noise voltage of these ampli-
fiers.Forinstance,a100Ωresistorinserieswitheachinput
would generate 1.8nV/√Hz of noise, and the total amplifier
noise voltage would rise from 1.9nV/√Hz to 2.6nV/√Hz.
Once the input differential voltage exceeds ±0.7V, steady
state current conducted though the protection diodes
should be limited to ±40mA. This implies 25Ω of protec-
tion resistance per volt of continuous overdrive beyond
±0.7V. The input diodes are rugged enough to handle
transient currents due to amplifier slew rate overdrive or
momentary clipping without these resistors.
Figure 2 shows the input and output waveforms of the
amplifier driven into clipping while connected in a gain
of AV = 1. When the input signal goes sufficiently beyond
the power supply rails, the input transistors will saturate.
When saturation occurs, the amplifier loses a stage of
phase inversion and the output tries to change states.
Diodes D1 and D2 forward bias and hold the output within
OV
Figure 2. VS = ±2.5V, AV = 1 with Large Overdrive
a diode drop of the input signal. In this photo, the input
signal generator is clipping at ±35mA, and the output
transistors supply this generator current through the
protection diodes.
With the amplifier connected in a gain of AV ≥ 2, the output
can invert with very heavy input overdrive. To avoid this
inversion, limit the input overdrive to 0.5V beyond the
power supply rails.
ESD
The LT6202/LT6203/LT6204 have reverse-biased ESD
protection diodes on all inputs and outputs as shown in
Figure 1. If these pins are forced beyond either supply,
unlimited current will flow through these diodes. If the
current is transient and limited to one hundred milliamps
or less, no damage to the device will occur.
Noise
The noise voltage of the LT6202/LT6203/LT6204 is equiva-
lent to that of a 225Ω resistor, and for the lowest possible
noise it is desirable to keep the source and feedback re-
sistance at or below this value, i.e. RS + RG||RFB ≤ 225Ω.
With RS + RG||RFB = 225Ω the total noise of the amplifier
is: en = √(1.9nV)2+(1.9nV)2 = 2.7nV. Below this resis-
tance value, the amplifier dominates the noise, but in the
resistanceregionbetween225Ωandapproximately10kΩ,
the noise is dominated by the resistor thermal noise. As
the total resistance is further increased, beyond 10k, the
noise current multiplied by the total resistance eventually
dominates the noise.
The product of en √ISUPPLY is an interesting way to gauge
lownoiseamplifiers.Manylownoiseamplifierswithlowen
have high ISUPPLY current. In applications that require low
noise with the lowest possible supply current, this product
can prove to be enlightening. The LT6202/LT6203/LT6204
have an en, √ISUPPLY product of 3.2 per amplifier, yet it is
commontoseeamplifierswithsimilarnoisespecifications
have an en √ISUPPLY product of 4.7 to 13.5.
For a complete discussion of amplifier noise, see the
LT1028 data sheet.
相关PDF资料 |
PDF描述 |
|---|---|
| 1-826375-6 | CONN MTIS SGL VERT BLACK 16POS |
| RMCF1206FT20K0 | RES 20K OHM 1/4W 1% 1206 SMD |
| 60598-7 | CONN UNINSUL RECEPT 20-24AWG |
| AD8426BCPZ-WP | IC AMP INSTR RR 1.5MHZ 16LFCSP |
| 61782-2 | CONN EDGE DISCONNECT 16-22AWG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT6205 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad Single Supply 3V, 100MHz Video Op Amps |
| LT6205_1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Single/Dual/Quad Single Supply 3V, 100MHz Video Op Amps |
| LT6205CS5 | 制造商:Linear Technology 功能描述:OP Amp Single Volt Fdbk R-R O/P ±6.3V/12.6V 5-Pin TSOT-23 |
| LT6205CS5#PBF | 制造商:Linear Technology 功能描述:SC-Amps/High Speed, Cut Tape 3V 100MHz, Video Op Amp |
| LT6205CS5#TR | 功能描述:IC OPAMP VID SGL 100MHZ TSOT23-5 RoHS:否 类别:集成电路 (IC) >> 线性 - 放大器 - 视频放大器和频缓冲器 系列:- 标准包装:1,000 系列:- 应用:驱动器 输出类型:差分 电路数:3 -3db带宽:350MHz 转换速率:1000 V/µs 电流 - 电源:14.5mA 电流 - 输出 / 通道:60mA 电压 - 电源，单路/双路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 供应商设备封装:20-QFN 裸露焊盘（4x4） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。