参数资料
| 型号： | LT1115CSW#TR |
| 厂商： | Linear Technology |
| 文件页数： | 15/16页 |
| 文件大小： | 0K |
| 描述： | IC OPAMP AUDIO MONO AB 16SOIC |
| 标准包装： | 1,000 |
| 放大器类型： | 音频 |
| 电路数： | 1 |
| 转换速率： | 15 V/µs |
| 增益带宽积： | 70MHz |
| 电流 - 输入偏压： | 50nA |
| 电压 - 输入偏移： | 50µV |
| 电流 - 电源： | 8.5mA |
| 电压 - 电源，单路/双路(±)： | ±4 V ~ 20 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 16-SO |
| 包装： | 带卷 (TR) |
LT1115
8
1115fa
Therefore, to realize truly low noise performance it is
important to understand the interaction between voltage
noise (en), current noise (in) and resistor noise (rn).
Total Noise vs Source Resistance
The total input referred noise of an op amp is given by
et = [en2 + rn2 + (inReq)2]1/2
where Req is the total equivalent source resistance at
the two inputs
and rn = √4kTReq = 0.13√Req in nV/√Hz at 25°C
As a numerical example, consider the total noise at 1kHz
of the gain of 1000 amplifier shown below.
Req = 100 + 100||100k ≈ 200
rn = 0.13√200 = 1.84nV/√Hz
en = 0.85nV/√Hz
in = 1.0pA/√Hz
et = [0.852 + 1.842 + (1.0 x 2.0)2]1/2 = 2.04nV/√Hz
output noise = 1000 et = 2.04V/√Hz
At very low source resistance (Req < 40) voltage noise
dominates. As Req is increased resistor noise becomes the
largest term—as in the example above—and the LT1115’s
voltage noise becomes negligible. As Req is further
increased, current noise becomes important. At 1kHz,
when Req is in excess of 20k, the current noise
component is larger than the resistor noise. The Total
Noise vs Matched Source Resistance plot in the Typical
Performance Characteristics section, illustrates the above
calculations.
–
+
100
100k
100
LT1115
LT1115 AI01
The plot also shows that current noise is more dominant
at low frequencies, such as 10Hz. This is because resistor
noise is flat with frequency, while the 1/f corner of current
noise is typically at 250Hz. At 10Hz when Req > 1k, the
current noise term will exceed the resistor noise.
When the source resistance is unmatched, the Total Noise
vs Unmatched Source Resistance plot should be con-
sulted. Note that total noise is lower at source resistances
below 1k because the resistor noise contribution is less.
When Rs > 1k total noise is not improved, however. This
is because bias current cancellation is used to reduce
input bias current. The cancellation circuitry injects two
correlated current noise components into the two inputs.
With matched source resistors the injected current noise
creates a common-mode voltage noise and gets rejected
by the amplifier. With source resistance in one input only,
the cancellation noise is added to the amplifier’s inherent
noise.
In summary, the LT1115 is the optimum amplifier for
noise performance—provided that the source resistance
is kept low. The following table depicts which op amp
manufactured by Linear Technology should be used to
minimize noise—as the source resistance is increased
beyond the LT1115’s level of usefulness.
Best Op Amp for Lowest Total Noise vs Source Resistance
Note 1: Source resistance is defined as matched or unmatched, e.g.,
RS = 1k means: 1k at each input, or 1k at one input and zero at the
other.
SOURCE RESISTANCE
BEST OP AMP
(NOTE 1)
AT LOW FREQ (10Hz)
WIDEBAND (1kHz)
0 to 400
LT1028/1115
400 to 4k
LT1007/1037
LT1028/1115
4k to 40k
LT1001*
LT1007/1037
40k to 500k
LT1012*
LT1001*
500k to 5M
LT1012* or LT1055
LT1012*
> 5M
LT1055
*These op amps are best utilized in applications requiring less bandwidth
than audio.
APPLICATIO S I FOR ATIO
WU
UU
相关PDF资料 |
PDF描述 |
|---|---|
| 77313-801-12LF | CONN HEADER .100 DUAL STR 12POS |
| LT1167IS8-1#PBF | IC INSTRUMENT AMP PROG 8SOIC |
| TSW-136-06-G-D | CONN HEADER 72POS .100" DL GOLD |
| LT2178CS8#PBF | IC OPAMP MICROPOWER DUAL 8-SOIC |
| TSW-136-05-G-D | CONN HEADER 72POS .100" DL GOLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT1116 | 制造商:LINER 制造商全称:Linear Technology 功能描述:4ns, 150MHz Dual Comparator with Independent Input/Output Supplies |
| LT1116_06 | 制造商:LINER 制造商全称:Linear Technology 功能描述:12ns, Single Supply Ground-Sensing Comparator |
| LT1116C | 制造商:LINER 制造商全称:Linear Technology 功能描述:12ns, Single Supply Ground-Sensiing Comparator |
| LT1116CN8 | 功能描述:IC COMPARATOR 12NS SINGLE 8-DIP RoHS:否 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 类型:通用 元件数:1 输出类型:CMOS，推挽式，满摆幅，TTL 电压 - 电源，单路/双路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 电压 - 输入偏移（最小值）:5mV @ 5.5V 电流 - 输入偏压（最小值）:1pA @ 5.5V 电流 - 输出（标准）:- 电流 - 静态（最大值）:24µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:450ns 磁滞:±3mV 工作温度:-40°C ~ 85°C 封装/外壳:6-WFBGA，CSPBGA 安装类型:表面贴装 包装:管件 其它名称:Q3554586 |
| LT1116CN8#PBF | 功能描述:IC COMPARATOR 12NS SINGLE 8-DIP RoHS:是 类别:集成电路 (IC) >> 线性 - 比较器 系列:UltraFast™ 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 类型:带电压基准 元件数:4 输出类型:开路漏极 电压 - 电源，单路/双路(±):2.5 V ~ 11 V，±1.25 V ~ 5.5 V 电压 - 输入偏移（最小值）:10mV @ 5V 电流 - 输入偏压（最小值）:- 电流 - 输出（标准）:0.015mA @ 5V 电流 - 静态（最大值）:8.5µA CMRR, PSRR（标准）:80dB CMRR，80dB PSRR 传输延迟（最大）:- 磁滞:- 工作温度:0°C ~ 70°C 封装/外壳:16-SOIC（0.154"，3.90mm 宽） 安装类型:表面贴装 包装:管件 产品目录页面:1386 (CN2011-ZH PDF) |
发布紧急采购，3分钟左右您将得到回复。