- 您现在的位置：买卖IC网 > PDF目录19180 > 91391-1 (TE Connectivity)SDE ERGO TL & DIE MICRO MNL PDF资料下载
参数资料
| 型号： | 91391-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/5页 |
| 文件大小： | 0K |
| 描述： | SDE ERGO TL & DIE MICRO MNL |
| 标准包装： | 1 |
| 系列： | MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，20-30 AWG |
| 特点： | 侧面插入，棘齿 |
408-10043
Contacts must not be re-terminated.
5. Tighten the nut and close the handles until the
ratchet releases.
6. Remove and inspect the contact.
7. Make another sample crimp. If the contact is
straight, tighten the contact support screw. If the
contact is still being bent during crimping, repeat the
adjustment procedure.
crimp height conforms to that shown in the table,
the tool is considered dimensionally correct. If not,
the tool must be adjusted. Refer to Section 7,
RATCHET ADJUSTMENT.
CAUTION Damaged product should not be used. If a
damaged contact is evident, it should be replaced.
!
NOTE
i
5. CRIMPING PROCEDURE
This tool is provided with a crimp adjustment
feature. Initially, the crimp height should be verified
as specified in Figure 3. Refer to Section 6, Crimp
Height Inspection, and Section 7, RATCHET
Adjustment, to verify crimp height before using the
tool to crimp desired contacts and wire sizes.
Refer to the table in Figure 1 and select wire of the
specified size and insulation diameter. Strip the wire to
the length indicated in Figure 1, taking care not to nick
or cut wire strands. Select an applicable contact and
identify the appropriate crimp section according to the
wire size markings on the tool. Refer to Figure 2 and
proceed as follows:
1. Hold the tool so that the back (wire side) is facing
Position Point on
Center of Wire
Barrel Opposite
Seam
Modified Anvil
WIRE SIZE
(AWG)
30-26
24-22
20
“A”
CRIMP HEIGHT
Dimension “A” and Tolerance (±)
0.58 ±0.05 [.023 ±.002]
0.74 ±0.05 [.029 ±.002]
0.89 ±0.05 [.035 ±.002]
attempt to crimp an improperly positioned contact.
you. Squeeze tool handles together and allow them
to open fully.
2. Holding the contact by the mating end, insert the
contact - insulation barrel first - through the front of
the tool and into the appropriate crimp section.
3. Position the contact so that the mating end of the
contact is on the locator side of the tool, and so that
the open “U” of the wire and insulation barrels must
face the top of the tool. Place the contact up into the
nest so that the movable locator drops into the slot
in the contact. Refer to Figure 2. Butt the front end
of the wire barrel against the movable locator.
CAUTION Make sure that both sides of the insulation barrel
are started evenly into the crimping section. Do not
!
6. CRIMP HEIGHT INSPECTION
Crimp height inspection is performed through the use
of a micrometer with a modified anvil, commonly
referred to as a crimp-height comparator.
TE Connectivity does not manufacture or market
crimp-height comparators. Detailed information on
obtaining and using crimp-height comparators can be
found in Instruction Sheet 408-7424.
Proceed as follows:
1. Refer to Figure 1 and select a wire (maximum
size) for each crimp section listed.
Figure 3
7. RATCHET ADJUSTMENT
Although the ratchet is preset prior to shipment, it is
important to verify the crimp height using a micrometer
or caliper. General use and subsequent wear may
cause the tool to go out of adjustment. It is
recommended that crimp height be inspected, and the
ratchet be adjusted, if necessary, on a regular basis.
Refer to Figure 4, and proceed as follows:
1. If the crimp height is larger than recommended,
remove the ratchet wheel adjustment screw and
rotate the adjustment wheel counterclockwise (+) to
a higher setting. Reinstall the screw. Repeat as
required.
2. If the crimp height is smaller than recommended,
remove the ratchet wheel adjustment screw and
rotate the adjustment wheel clockwise (-) to a lower
setting. Reinstall the screw. Repeat as required.
3. If the crimp cannot be made to conform to the
recommended crimp height, the tool or die set must
be replaced. See Section 9, REPLACEMENT.
2. Refer to Section 5, CRIMPING PROCEDURE,
and crimp the contact(s) accordingly.
3. Using a crimp height comparator, measure the
wire barrel crimp height listed in Figure 3. If the
Rev C
Adjustment
Screw
Figure 4
Ratchet
Adjustment
Wheel
3 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 492782-1 | TOOL HAND W/DIE SET |
| 69363 | TOOL HAND DAHT SOLIS 20-26AWG |
| 90683-1 | PRO-CRIMPER ASSEMBLY |
| 229451-2 | PALM GRIP TOOL & 50 POSN SLIDE |
| 58499-1 | TOOL PRO CRIMPER II W/DI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913-911 | 制造商:SPC Multicomp 功能描述:CAPACITOR 105C 47UF 100V |
| 91391-2 | 功能描述:冲压机与冲模 SDE ERGO DIE MICRO MNL RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 913913 | 功能描述:DINRAIL 35-7.5MM SLOT ST 50.8MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
| 913914 | 功能描述:TS 35/7.5 SL ST PRE CUT 3 76.2MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
| 913915 | 功能描述:DINRAIL 35-7.5MM SLOT ST 101.6MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
发布紧急采购，3分钟左右您将得到回复。