- 您现在的位置：买卖IC网 > PDF目录19180 > 91391-1 (TE Connectivity)SDE ERGO TL & DIE MICRO MNL PDF资料下载
参数资料
| 型号： | 91391-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/5页 |
| 文件大小： | 0K |
| 描述： | SDE ERGO TL & DIE MICRO MNL |
| 标准包装： | 1 |
| 系列： | MATE-N-LOK |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 矩形触点，20-30 AWG |
| 特点： | 侧面插入，棘齿 |
408-10043
NOTE
i
2. Place the wire anvil and insulation anvil so that
their chamfered sides and their marked surfaces
face outward, when mounted in the moving jaw of
the tool frame.
3. Insert the two die retaining pins.
4. Insert the short die retaining screw through the
jaw and through both anvil dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
5. Place the wire crimper and insulation crimper so
11. To disassemble, close the tool handles until the
ratchet releases, remove the nut, the locator
assembly, the two die retaining screws, and the four
die retaining pins, and slide the anvils and crimpers
out of the tool jaws.
The ratchet has detents with audible “clicks” as the
handles are closed. The ratchet releases on the
sixth “click”.
4. CONTACT SUPPORT ADJUSTMENT (Figure 2)
that their chamfered sides and their marked
surfaces face outward, when mounted in the
stationary jaw of the tool frame.
6. Insert the two die retaining pins.
NOTE
i
The contact support is preset prior to shipment, but
minor adjustment may be necessary.
7. Insert the long die retaining screw through the
jaw and through both crimper dies, and tighten the
screw just enough to hold the dies in place. Do not
tighten the screw completely at this time.
8. Carefully close the tool handles, making sure that
1. Make a sample crimp and determine if the
contact is straight, bending upward, or bending
downward.
2. If adjustment is required, loosen the screw that
holds the contact support onto the locator assembly.
the anvils and crimpers align properly. Continue
closing the tool handles until the ratchet in the tool
frame has engaged sufficiently to hold the anvils
and crimpers in place, then tighten both die
NOTE
i
The ratchet has detents that create audible clicks
as the tool handles are closed.
retaining screws.
9. Place the locator assembly over the end of the
long screw, and position the locator assembly
against the side of the tool jaw.
10. Place the nut onto the end of the long screw and
tighten the nut enough to hold the locator assembly
in place, while still allowing the locator to slide up
and down.
3. Place a contact with wire into the proper nest and
close the tool handles until the ratchet reaches the
sixth click, or until the contact support touches the
contact.
4. Slightly loosen the nut that holds the locator
assembly onto the tool frame.
Contact
Support
Locator
Adjustment
Screw for
Contact
Support
Back of Tool
(Wire Side)
Wire
Contact
(Typ)
Locator in
Wire Stop
Slot
Strip Length
Wire Inserted
to Stop
Figure 2
Rev C
2 of 5
相关PDF资料 |
PDF描述 |
|---|---|
| 492782-1 | TOOL HAND W/DIE SET |
| 69363 | TOOL HAND DAHT SOLIS 20-26AWG |
| 90683-1 | PRO-CRIMPER ASSEMBLY |
| 229451-2 | PALM GRIP TOOL & 50 POSN SLIDE |
| 58499-1 | TOOL PRO CRIMPER II W/DI |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 913-911 | 制造商:SPC Multicomp 功能描述:CAPACITOR 105C 47UF 100V |
| 91391-2 | 功能描述:冲压机与冲模 SDE ERGO DIE MICRO MNL RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 913913 | 功能描述:DINRAIL 35-7.5MM SLOT ST 50.8MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
| 913914 | 功能描述:TS 35/7.5 SL ST PRE CUT 3 76.2MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
| 913915 | 功能描述:DINRAIL 35-7.5MM SLOT ST 101.6MM RoHS:是 类别:硬件，紧固件，配件 >> 通道，DIN 导轨 系列:- 产品目录绘图:Unslotted 35x15mm 标准包装:1 系列:- 尺寸:1.378" W x 0.591" H（35.00mm x 15.00mm） 长度:67.000"（1701.80mm） 开槽/无槽:无槽 厚度:0.059"（1.50mm） 其它名称:ADR3515-U6700 |
发布紧急采购，3分钟左右您将得到回复。