参数资料
型号: 71M6521FE-DB
厂商: Maxim Integrated Products
文件页数: 43/107页
文件大小: 0K
描述: BOARD DEMO FOR 71M6521FE
产品培训模块: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
标准包装: 1
主要目的: 电源管理,电度表/功率表
嵌入式:
已用 IC / 零件: 71M6521
已供物品: 2 个板,线缆,CD,电源
71M6521DE/DH/FE Data Sheet
EEPROM Interface
The 71M6521DE/DH/FE provides hardware support for either type of EEPROM interface, a two-pin interface and a
three-pin interface. The interfaces use the EECTRL and EEDATA registers for communication.
Two-Pin EEPROM Interface
The dedicated 2-pin serial interface communicates with external EEPROM devices. The interface is multiplexed onto
pins DIO4 (SCK) and DIO5 (SDA) controlled by the DIO_EEX bit I/O RAM (see I/O RAM Table). The MPU
communicates with the interface through two SFR registers: EEDATA and EECTRL . If the MPU wishes to write a byte
of data to EEPROM, it places the data in EEDATA and then writes the ‘Transmit’ command (CMD = 0011) to EECTRL .
This initiates the transmit operation. The transmit operation is finished when the BUSY bit falls. Interrupt INT5 is also
asserted when BUSY falls. The MPU can then check the RX_ACK bit to see if the EEPROM acknowledged the
transmission.
A byte is read by writing the ‘Receive’ command (CMD = 0001) to EECTRL and waiting for the BUSY bit to fall. Upon
completion, the received data is in EEDATA . The serial transmit and receive clock is 78kHz during each transmission,
and the clock is held in a high state until the next transmission. The bits in EECTRL are shown in Table 57.
The EEPROM interface can also be operated by controlling the DIO4 and DIO5 pins directly (“bit-banging”).
However, controlling DIO4 and DIO5 directly is discouraged, because it may tie up the MPU to the point
where it may become too busy to process interrupts .
Status
Bit
7
6
5
4
Name
ERROR
BUSY
RX_ACK
TX_ACK
Read/
Write
R
R
R
R
Reset
State
0
0
1
1
Polarity
Positive
Positive
Negative
Negative
Description
1 when an illegal command is received.
1 when serial data bus is busy.
0 indicates that the EEPROM sent an ACK bit.
0 indicates when an ACK bit has been sent to the EEPROM
CMD
0000
Operation
No-op. Applying the no-op command will stop the I 2 C clock
(SCK, DIO4). Failure to issue the no-op command will keep
the SCK signal toggling.
3-0
CMD
[3:0]
W
0
Positive,
see CMD
Table
0001
0011
0101
Receive a byte from EEPROM and send ACK.
Transmit a byte to EEPROM.
Issue a ‘STOP’ sequence.
0110
1001
Others
Receive the last byte from EEPROM, do not send ACK.
Issue a ‘START’ sequence.
No Operation, set the ERROR bit.
Table 57: EECTRL Status Bits
Rev 3
Page: 43 of 107
相关PDF资料
PDF描述
71M6531F-DB BOARD DEMO 71M6531F
71M6533-DB BOARD DEMO 71M6533
71M6534H-DB BOARD DEMO 71M6534H
71M6541F-DB DEMO BOARD 71M6541F
71M6543F-DB-CT DEMO BOARD 71M6543F-DB-CT
相关代理商/技术参数
参数描述
71M6521FE-IGT 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC
71M6521FE-IGT/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6521FE-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6521FE-IGTR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC
71M6521FE-IGTR/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel