- 您现在的位置：买卖IC网 > Datasheet目录600 > 58338-1 (TE Connectivity)PWR BENCH ASSEMBLY W/O HEADS Datasheet资料下载
参数资料
| 型号： | 58338-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | PWR BENCH ASSEMBLY W/O HEADS |
| 标准包装： | 1 |
| 工具类型： | 气动工作台组件 - 无模具 |
| 适用于相关产品： | 端子接头 |
| 配用： | A28718-ND - HEAD (IDC) MODU MTE W/O TL A2032-ND - HEAD ASSEMBLY TOOL FOR D-SUB CON A2040-ND - HEAD ASSEMBLY TOOL FOR AMP MT CO |
| 其它名称： | Q1197143 |
408-9393
2. Align the contact to be terminated with the wire
inserter of the head. Make sure that the locating
pawl rests between the connector index ribs.
3. Insert an unstripped wire into the funnel area
between the contact and the wire inserter until it
bottoms on the tool base.
4. Depress the footswitch and hold it until the wire
inserter bottoms.
5. Release the footswitch. The wire inserter will
retract and the feed slide will automatically advance
the connector to the next contact position.
6. Repeat steps 2 through 5 until all contacts have
been terminated.
7. Inspect each termination.
7. MAINTENANCE AND INSPECTION
DANGER To avoid personal injury, ALWAYS DISCONNECT
the power bench assembly from the air supply
STOP when performing maintenance or inspection
procedures.
These procedures have been established to ensure
the quality and reliability of the power bench assembly.
A brief inspection should be made daily by the
operator and a more detailed inspection should be
performed on a scheduled basis by quality control
personnel.
7.1. Daily Maintenance
Each operator of the unit should be made aware of,
and responsible for, the following procedures:
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or clean, lint-free cloth. DO
NOT use objects that could damage the power
bench assembly.
2. Ensure that all components are in place and
properly secured.
3. With the terminating head or feed track assembly
in place, connect the air supply and actuate the
power assembly by depressing and releasing the
foot switch to ensure that the mechanisms and
plunger move smoothly and freely.
7.2. Periodic Inspection (At Least Once a Month)
Regular inspections should be performed by quality
control personnel. A record of quality control
inspections should remain with the power bench
assembly or with personnel responsible for the
assembly. It is recommended that one inspection per
month be performed; however, operator training and
skill, amount of use, working conditions, and
established company standards are all factors to be
considered in scheduling inspections.
The inspections should be performed in the following
sequence:
Rev E
1. Remove any accumulated film with a suitable
cleaning agent that will not affect plastic material.
2. Make certain that all components are in place and
properly secured. Check air tube fittings for leaks.
3. Make a few test terminations and inspect the
terminations in accordance with the inspection
procedure described in the instructions packaged
with the terminating head or feed track assembly.
4. Check for chipped, cracked, worn, or broken
areas. If damage is evident, repair is necessary.
See Section 8, REPLACEMENT AND REPAIR.
8. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 5.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed should
be replaced by TE to ensure quality and reliability.
Order replacement parts through your TE
representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
CUSTOMER SERVICE (038-035) ?
TYCO ELECTRONICS CORPORATION ?
P0 BOX 3608 ?
HARRISBURG, PA 17105-3608
or
TYCO ELECTRONICS CORPORATION UK LTD ?
BARTON TORS ?
BIDEFORD ?
NORTH DEVON, GREAT BRITAIN
For customer repair service, call 1-800-526-5136.
9. REVISION SUMMARY
Since the previous release of these instructions, the
format was changed.
5 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 58372-1 | TOOL HEAD ASSEM 2MM TERMINATER |
| 58425-3 | TOOL DIE SET COAX RG59 DB |
| 58430-1 | TOOL REPAIR .050 SERIES |
| 58432-1 | TOOL DIE SET |
| 58433-4 | TOOL CRIMP F/OPTIC ST & SC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 583389-000 | 制造商:TE Connectivity 功能描述:Quick Disconnect Terminal 10-12AWG RCP Tin Bulk 制造商:TE Connectivity 功能描述:QUICK DISCONNECT TERMINAL 10-12AWG F 33.02MM 6.35MM TN BULK - Bulk 制造商:TE Connectivity 功能描述:CONN RCPT PUSH-ON 12-10AWG YELLW 制造商:TE Connectivity 功能描述:TERMINAL SOCKET 12-10AWG 制造商:TE Connectivity 功能描述:TERMINAL, SOCKET, 12-10AWG 制造商:TE Connectivity / Raychem 功能描述:TERMINAL, SOCKET, 12-10AWG; Connector Type:Disconnect; Series:DuraSeal; Insulator Colour:Yellow; Termination Method:Crimp; Stud/Tab Size:6.35mm x 0.81mm; Wire Size AWG Min:12AWG; Wire Size AWG Max:10AWG; Contact Material:Copper; ;RoHS Compliant: Yes 制造商:TE Connectivity 功能描述:B-106-3633 |
| 583393-000 | 功能描述:电缆固定件和配件 S1125-KIT-5 RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 5833A20001A | 制造商:LG Corporation 功能描述:Fan Assembly,Blower |
| 5833B-440 | 制造商:Crane Connectors 功能描述: 制造商:CRANE PUMPS AND SYSTEMS I 功能描述: |
| 5833P | 制造商:AGERE 制造商全称:AGERE 功能描述:5833P Diplexer, Full-Duplex, Bidirectional, Single-Fiber, Data and Voice Transceivers |
发布紧急采购，3分钟左右您将得到回复。