- 您现在的位置：买卖IC网 > Datasheet目录600 > 58338-1 (TE Connectivity)PWR BENCH ASSEMBLY W/O HEADS Datasheet资料下载
参数资料
| 型号： | 58338-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 3/6页 |
| 文件大小： | 0K |
| 描述： | PWR BENCH ASSEMBLY W/O HEADS |
| 标准包装： | 1 |
| 工具类型： | 气动工作台组件 - 无模具 |
| 适用于相关产品： | 端子接头 |
| 配用： | A28718-ND - HEAD (IDC) MODU MTE W/O TL A2032-ND - HEAD ASSEMBLY TOOL FOR D-SUB CON A2040-ND - HEAD ASSEMBLY TOOL FOR AMP MT CO |
| 其它名称： | Q1197143 |
408-9393
DANGER
STOP
Denotes an imminent hazard which may result in
moderate or severe injury.
The bench mount is designed to be mounted in either
of the two positions shown in Figure 2. Orientation of
the bench mount depends on operator preference and
the desired eject direction of terminated connector
(refer to Figure 4). Install the bench mount as follows:
CAUTION Denotes a condition which may result in product or
equipment damage.
!
1. Place the bench mount on a bench or work table
in the desired location and orientation.
2. Mark the location for the screws in the bench
surface through the drilled holes of the bench mount
flange. Drill holes for the mounting screws.
NOTE
i
Highlights special or important information.
NOTE
i
Mounting hardware is not supplied with the power
bench assembly and must be supplied by the
customer.
3. DESCRIPTION (see Figure 2)
The power bench assembly consists of a bench mount
with an attached pneumatic power assembly, a foot
switch, and air tubes which connect the foot switch to
the power assembly and the air source to the foot
switch.
The bench mount is attached to a bench or work table
with screws or clamps and the foot switch is used to
actuate the power assembly when connected to an air
source.
3. Secure the screws.
4. Connect the air tube to an approved air source. It
is recommended that a filter-regulator-lubricator unit
with the lubricator adjusted to the minimum setting
be used with the power bench assembly. Refer to
disconnect fittings are used to connect the tool to
the air-supply. If not using quick-disconnect fittings,
provide a pneumatic lock-out on the air line that
bleeds air after it is turned off.
In this use, the pneumatic power bench assembly
emits a noise level less than 70 dB and the vibration
level is less than 2.5 mm/s2.
4. INSTALLATION
DANGER To avoid personal injury, ALWAYS disconnect
handle assembly from the air supply when installing
STOP or removing the bench mount.
Air Tube to ?
Foot Switch
Pneumatic Power ?
Assembly
Bench ?
Mount
Key
NOTE
i
The power assembly is designed to operate at an
air pressure range of 276 through 483 kPa [40
through 70 psi]. Service life of the power assembly
can be greatly extended when only the necessary
air pressure is applied. Excessive pressure causes
unnecessary wear and strain on the power
assembly, terminating head or feed track assembly,
and connectors.
Terminating Head ((Ref)
Terminating Head ?
((Ref)
Bench or
Work Table
Rev E
Mounting Hardware ?
(Customer Supplied)
Figure 2
Air Tube to ?
Foot Switch
3 of 6
相关PDF资料 |
PDF描述 |
|---|---|
| 58372-1 | TOOL HEAD ASSEM 2MM TERMINATER |
| 58425-3 | TOOL DIE SET COAX RG59 DB |
| 58430-1 | TOOL REPAIR .050 SERIES |
| 58432-1 | TOOL DIE SET |
| 58433-4 | TOOL CRIMP F/OPTIC ST & SC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 583389-000 | 制造商:TE Connectivity 功能描述:Quick Disconnect Terminal 10-12AWG RCP Tin Bulk 制造商:TE Connectivity 功能描述:QUICK DISCONNECT TERMINAL 10-12AWG F 33.02MM 6.35MM TN BULK - Bulk 制造商:TE Connectivity 功能描述:CONN RCPT PUSH-ON 12-10AWG YELLW 制造商:TE Connectivity 功能描述:TERMINAL SOCKET 12-10AWG 制造商:TE Connectivity 功能描述:TERMINAL, SOCKET, 12-10AWG 制造商:TE Connectivity / Raychem 功能描述:TERMINAL, SOCKET, 12-10AWG; Connector Type:Disconnect; Series:DuraSeal; Insulator Colour:Yellow; Termination Method:Crimp; Stud/Tab Size:6.35mm x 0.81mm; Wire Size AWG Min:12AWG; Wire Size AWG Max:10AWG; Contact Material:Copper; ;RoHS Compliant: Yes 制造商:TE Connectivity 功能描述:B-106-3633 |
| 583393-000 | 功能描述:电缆固定件和配件 S1125-KIT-5 RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 5833A20001A | 制造商:LG Corporation 功能描述:Fan Assembly,Blower |
| 5833B-440 | 制造商:Crane Connectors 功能描述: 制造商:CRANE PUMPS AND SYSTEMS I 功能描述: |
| 5833P | 制造商:AGERE 制造商全称:AGERE 功能描述:5833P Diplexer, Full-Duplex, Bidirectional, Single-Fiber, Data and Voice Transceivers |
发布紧急采购，3分钟左右您将得到回复。