- 您现在的位置：买卖IC网 > PDF目录18619 > 311386-3 (TE Connectivity)90DEG BEND SEGMENT RG-405/U PDF资料下载
参数资料
| 型号： | 311386-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 9/12页 |
| 文件大小： | 0K |
| 描述： | 90DEG BEND SEGMENT RG-405/U |
| 标准包装： | 1 |
| 系列： | * |
408-6788
i NOTE Make sure that the shoulders of the conforming block
Spacer Used
with SMA Plugs
Cable Bending
Dummy Jack
NOTE
bear on the bottom surface of the tool holder BEFORE
applying pressure in the vise.
7. Tighten the vise to force the conforming block into
the slot. Continue to tighten until the legs of the tool
Figure 14
Bending RG-402 Cable to 6.35mm [.250 in.] Radius or
RG-405 Cable to 3.18mm [.125 in.] Radius
Tool Holder
Bend Segment
Oriented Properly
Apply Finger Pressure
Plugs Screwed
onto Tool Holder
Figure 15
Bending RG-402 Cable to 3.18 mm [.125 in.] Radius
holder prevent further movement of the vise jaws.
8. Remove the assembly from the vise, and
unscrew the plug from the fixture.
9. Remove the conforming block and bend
segment.
8.3. To Make 1.57 mm [.062 in.] Bends on RG-405 Cable
It is recommended that a special kit be used to make
1.57 mm [.062 in.] bends on RG-405 cable. Kit
220224-2 includes a limiting pin, a 90° bend tool body
assembly, a 90° bend segment, and a conforming
block. The figures referenced for the 6.35 mm
[.250 in.] and 3.18 mm [.125 in.] bends will assist in
making the 1.57 mm [.062 in.] bends. These steps are
recommended:
1. Make the 3.18 mm [.125 in.] radial bend as
described in Paragraph 8.1, and remove the plug
from the tool holder.
2. Replace the 3.18 mm [.125 in.] bend segment
with the special 1.57 mm [.062 in.] bend segment,
which is a part of Kit 220224-2.
3. Re-attach the plug to the dummy jack of the tool
holder.
Tongue
Cable Previously
Formed to 6.35
[.250] Radius
Bend
Tool Holder
3.18 [.125]
Radius Bend
Segment
Limiting Pin
Conforming
Block Shoulder
4. Place the special 1.57 mm [.062 in.] conforming
block over the cable with the tongue of the block in
the tool holder slot. The conforming block is part of
Kit 220224-2.
5. Insert the limiting pin and slide the block against
the tool holder.
6. Place the assembly in a vise with a 69.85 mm
[2.75 in.] opening.
7. Remove the assembly from the vise, and
unscrew the plug from the fixture.
8. Remove the assembly from the vise, and
unscrew the plug from the fixture.
9. Remove the special conforming block and special
bend segment.
9. MAINTENANCE AND INSPECTION
Legs of Tool Holder Prevent Further
Movement of Vise Against Conforming Block
Figure 16
6. Place the assembly in a vise with a 69.85 mm
[2.75 in.] opening.
Rev L
Hand Crimping Tool and Cable Preparation Kit
59981-1 is inspected before shipment. The tool and kit
should be inspected immediately upon arrival to
ensure that they have not been damaged during
shipment, and that they perform according to the
criteria described in this sheet. If the tool and kit are
damaged upon arrival, retain the shipping container,
file a claim with the carrier, and notify TE immediately.
9 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 476P6P144 | CABLE STR MALE-MALE 6POS 12' |
| 1912P36 | CABLE SGL-END STR MALE 12POS 3' |
| GP1UM277XK | RECEIVER REMOTE CTRL TOP 56.8KHZ |
| GP1UM262XK0F | RECEIVER REMOTE CTRL TOP 36.7KHZ |
| 553P3S36 | CBL STR MALE-R/A FEMALE 3POS 3' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 311392-1 | 制造商:TE Connectivity 功能描述:90 DEGREE BEND TOOL BODY ASSY - Bulk |
| 311395-1 | 功能描述:手工工具 CUT-OFF FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 311396-1 | 功能描述:手工工具 CABLE DRESSING FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 31-1397 | 制造商:TDK-EPC 功能描述:4 drum spill pallet ramp |
| 31-1398 | 制造商:TDK-EPC 功能描述:2 drum spill pallet ramp |
发布紧急采购，3分钟左右您将得到回复。