- 您现在的位置：买卖IC网 > PDF目录18619 > 311386-3 (TE Connectivity)90DEG BEND SEGMENT RG-405/U PDF资料下载
参数资料
| 型号： | 311386-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/12页 |
| 文件大小： | 0K |
| 描述： | 90DEG BEND SEGMENT RG-405/U |
| 标准包装： | 1 |
| 系列： | * |
408-6788
i NOTE All cable terminated with connectors without center
i NOTE Special die sets and special locators are NOT supplied
i NOTE The cable can also be prepared by using Semi-Rigid
i NOTE On preformed cables with 90° or 180° bends, a
The kit also includes the following cable preparation
tools: cable dressing fixture, trimmer tool, cable cutoff
fixture, and 90° bending fixture assembly.
NOTE
with Kit 59981-1. These items MUST be ordered
separately. They include: (1) RG-402 cable, Die Set
312962-1 for plugs with retractable collars, and Locator
313585-1 for sealed plugs without center contacts; and
(2) RG-405 cable, Die Set 313113-1, and Locator
220221-3 for short plugs, and Locator 312173-1 for
right-angle plugs.
3. CABLE, CONNECTOR, AND LOCATOR SELECTION
Select the correct combination of cable, connector,
hand tool locator, and die set from Figure 2.
4. CABLE PREPARATION
Semi-rigid cable must be properly prepared for
termination. Correct use of cable preparation tools
(cutoff fixture, dressing fixture, and trimming tool) will
give the strip length and recommended pointing as
shown in Figure 3, Detail A.
If TE Connectivity tools are not used for cable
preparation, strip the cable to the dimension shown,
and deburr (point) the center conductor as shown in
Figure 3, Detail B, then proceed directly to Section 5,
TOOL SETUP.
Cable Preparation-Strip Length and Pointing
NOTE
contacts must be pointed to ensure a sound connection.
3. Trim the cable dielectric to the strip length
dimension shown in Figure 3. Be careful to avoid
nicking the center conductor.
4. Brush the prepared cable end to remove any
metallic debris that might be present.
NOTE
Cable Stripping Machine 220211-2 with Stripping Kit
813599-[ ]. Refer to Customer Manual 409-2909 for
detailed operating procedures.
4.1. Cable Cutoff Fixture (Figure 4)
Clamp the cable to the fixture, with the cable in the
proper groove, and cut the cable end squarely with a
jeweler's saw with a 0.28 to 0.33 mm [.011 to .013 in.]
blade thickness.
NOTE
minimum straight cable length of 12.70 mm [.500 in.] is
required to clear the tool head during crimping.
Cable Cutoff Fixture
Clamp
Screws
Detail A
Recommended?
Detail B
Optional
90°
Deburr Around Edge of
Center Conductor
60-90°
Strip Length
Cable Size
Designations
Cable
Saw Blade
in Slot
?Required on cables
terminated to connectors
without center contacts
CABLE
Note: Not to Scale
STRIP LENGTH DIMENSION
NOTE: Enter preformed cable from this end of fixture if cut
end is desired up to 12.70 mm [.500 in.] of cable bend radius.
Minimum straight cable length of 12.70 mm [.50 in.] is
required for cable bend to clear tool head during crimping.
Figure 4
RG-402, RG-405
Figure 3
2.16 ±0.13 [.085 ±.005]
4.2. Cable Dressing Fixture and Trimmer Tool
1. Place the cable dressing fixture in a vise.
To prepare the cable:
1. Strip the outer cable jacket to the dimension
provided in Figure 3. Make sure that the cut is at a
90° angle to the cable length.
2. Point the center conductor.
Rev L
2. Insert the cable into the hole corresponding to the
cable size as shown in Figure 5, Detail A.
3. Using the jeweler's saw, carefully cut through the
cable shield while rotating the cable, maintaining
pressure against the fixture.
4 of 12
相关PDF资料 |
PDF描述 |
|---|---|
| 476P6P144 | CABLE STR MALE-MALE 6POS 12' |
| 1912P36 | CABLE SGL-END STR MALE 12POS 3' |
| GP1UM277XK | RECEIVER REMOTE CTRL TOP 56.8KHZ |
| GP1UM262XK0F | RECEIVER REMOTE CTRL TOP 36.7KHZ |
| 553P3S36 | CBL STR MALE-R/A FEMALE 3POS 3' |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 311392-1 | 制造商:TE Connectivity 功能描述:90 DEGREE BEND TOOL BODY ASSY - Bulk |
| 311395-1 | 功能描述:手工工具 CUT-OFF FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 311396-1 | 功能描述:手工工具 CABLE DRESSING FIXTURE RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 31-1397 | 制造商:TDK-EPC 功能描述:4 drum spill pallet ramp |
| 31-1398 | 制造商:TDK-EPC 功能描述:2 drum spill pallet ramp |
发布紧急采购，3分钟左右您将得到回复。