- 您现在的位置：买卖IC网 > PDF目录19106 > 11-01-0101 (Molex Connector Corporation)TOOL HAND CRIMP 14-20AWG PDF资料下载
参数资料
| 型号： | 11-01-0101 |
| 厂商： | Molex Connector Corporation |
| 文件页数： | 6/24页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP 14-20AWG |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 端子，14-20 AWG |
| 特点： | 侧面插入 |
| 配用： | WM2684CT-ND - CONN FEMALE FLAT BLADE 14-22AWG WM2684TR-ND - CONN FEMALE FLAT BLADE 14-22AWG |
| 其它名称： | 0011-01-0101 0011-01-0101-E 0011010101 0011010101-E 11-01-0101-E 11010101 11010101-E |
Quality Crimp Handbook
SECTION 4
DEFINITIONS
BEND UP
BRUSH
BELL
MOUTH
CONDUCTOR
CRIMP
SEAM
ROLLING
INSULATION
CRIMP
STRIP
LENGTH
CUT-OFF
TAB
CRIMP
BEND
DOWN
TWISTING
TERMINAL CROSS
SECTION VIEW
EXTRUSIONS
HEIGHT
EXTRUSION
Anatomy of a Crimp Termination (Figure 4-1)
Bell Mouth (Flare)
The flare that is formed on the edge of the
conductor crimp acts as a funnel for the wire
strands. This funnel reduces the possibility that a
sharp edge on the conductor crimp will cut or nick
the wire strands. As a general guideline, the
conductor bell mouth needs to be approximately 1
to 2 times the thickness of the terminal material. *
Bend Test
One way to test the insulation crimp is by bending
the wire several times and then evaluating the
movement of the insulation and wire strands. As a
rule, the insulation crimp should withstand the wire
being bent 60 to 90 degrees in any direction,
several times. Use care when working with small
wire sizes so the wire at the back of the insulation
crimp does not shear.
Conductor Brush
The conductor brush is made up of the wire strands
that extend past the conductor crimp on the contact
side of the terminal. This helps ensure that
EXTRUSION
Figure 4-1
mechanical compression occurs over the full length of
the conductor crimp. The conductor brush should not
extend into the contact area.
Conductor Crimp
This is the metallurgical compression of a terminal
around the wire's conductor. This connection creates a
common electrical path with low resistance and high
current carrying capabilities.
Conductor Crimp Height
The conductor crimp height is measured from the top
surface of the formed crimp to the bottom radial surface.
Do not include the extrusion points in this measurement
(See Figure 4-1). Measuring crimp height is a quick,
non-destructive way to help ensure the correct
metallurgical compression of a terminal around the
wire's conductor and is an excellent attribute for process
control. The crimp height specification is typically set as
a balance between electrical and mechanical
performance over the complete range of wire stranding
and coatings, and terminal materials and plating.
Although it is possible to optimize a crimp height to
individual wire stranding and terminal plating, one crimp
height specification is normally created.
*Consult individual terminal specification requirements
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 6 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 555-5403F | LED CBI 2MM YLW 5V RES QUAD TH |
| ASFLMPC-25.000MHZ-Z-T | OSC 25.000 MHZ CMOS MEMS SMD |
| 555-5009F | LED CBI 2MM RED 5V RES QUAD TH |
| P51-50-A-O-P-5V-000-000 | SENSOR 50PSI 7/16-20 UNF 2B 5V |
| P51-15-A-O-P-5V-000-000 | SENSOR 15PSI 7/16-20 UNF 2B 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 11-01-0103 | 功能描述:折皱器 CRIMP HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 11-01-0105 | 功能描述:折皱器 PNEUMATIC HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1101-01-0519 | 制造商:Concord Electronics Inc 功能描述:PTFE Insulated Terminal PIN 8.3mm 4.36mm Electro-Solder Over Copper |
| 11-01-0107 | 制造商:MOLEX 功能描述: |
| 11-01-0110 | 功能描述:手工工具 HAND TOOL-40682 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。