- 您现在的位置：买卖IC网 > PDF目录19106 > 11-01-0101 (Molex Connector Corporation)TOOL HAND CRIMP 14-20AWG PDF资料下载
参数资料
| 型号： | 11-01-0101 |
| 厂商： | Molex Connector Corporation |
| 文件页数： | 15/24页 |
| 文件大小： | 0K |
| 描述： | TOOL HAND CRIMP 14-20AWG |
| 其它有关文件： | Overlap Style Insulation Crimps |
| 标准包装： | 1 |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 端子，14-20 AWG |
| 特点： | 侧面插入 |
| 配用： | WM2684CT-ND - CONN FEMALE FLAT BLADE 14-22AWG WM2684TR-ND - CONN FEMALE FLAT BLADE 14-22AWG |
| 其它名称： | 0011-01-0101 0011-01-0101-E 0011010101 0011010101-E 11-01-0101-E 11010101 11010101-E |
Quality Crimp Handbook
SECTION 8
CRIMP PROCESS CONTROL
The crimp process is the interaction of a terminal, wire,
tooling, personnel, methods and procedures, and
environmental attributes. When this process is
controlled, it will produce a quality termination. Quality
control is an important part of quality crimping. It
should not take excessive setup or inspection time to
do, and it can save a harness manufacturer thousands
of dollars in potential rework or re-manufacturing.
Variability is the slight change that occurs from crimp to
crimp. There are two types of variability, common or
special. Common causes of variation affect the
process uniformly and are the result of many small
sources. Common variability is inherent tolerances
within a reel of wire or terminals. Common variability
also is created by the natural tolerances of the stripping
and crimping machines.
Reducing variability at the common level typically has
* PPM - Parts per million potential defects.
A 25 piece minimum sample needs to be taken from
the crimping process. Calculate the average and
standard deviation for the sample. A capability index is
defined by the formula below. C p may range in value
from zero to infinity, with a larger value indicating a
more capable process. A value greater than 1.33 is
considered acceptable for most applications. C p is
calculated with the following formula.
___Tolerance___
6*Standard Deviation
The C pk index indicates whether the process will
produce units within the tolerance limits. C pk has a
value equal to C p if the process is centered on the
mean of specification; if C pk is negative, the process
mean is outside the specification limits; if C pk is
between 0 and 1 then some of the 6 sigma spread falls
outside the tolerance limits. If C pk is larger than one,
the 6-sigma spread is completely within the tolerance
limits. C pk is calculated with the lesser of the following
formulas:
to come from changes to the wire, terminal, and tooling
manufacturer.
__(USL - Mean)__
3*Standard Deviation
__ (Mean - LSL)__
3*Standard Deviation
Special causes of variation occur irregularly and
unpredictably. Without checks throughout a run, having
a tool become loose after the first hundred crimps or a
jam resulting from a damaged tool may be undetected
until thousands of crimps are made.
Process Capability
Before putting a new crimping tool in production, Molex
recommends that each customer do a capability study,
using the specific wire that will be used in its process.
A capability study, which is based on the assumption of
a normal distribution (bell-type curve), estimates the
probability of a measurement being outside of
specification.
USL = Upper Specification Limit, LSL = Lower
Specification Limit
Six sigma is a goal of many companies because it
represents virtually zero defects. The ability of a
company to achieve a six-sigma level depends on the
amount of common variability in its process. For
example, hand stripping the wire produces more
variability than a stripping machine; crimping hand tools
produce more variability than a press and die set, and
bench terminations produce more variability than a
wire-processing machine.
A part of the variability in crimping will result from the
type of instruments that are used to measure the parts
C pk
0.67
1
1.33
1.67
2
Capability
+/- Sigma % Yield
2 95.45
3 99.73
4 99.99
5 99.99+
6 99.99++
PPM*
45,500
2,699
63
0.57
0
and the operator's ability to repeat the measurement. A
crimp micrometer will measure more accurately than a
dial caliper. An automatic pull force system will
measure better than a hook type scale. It is important
that the measurement gauge has enough resolution.
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 15 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| 555-5403F | LED CBI 2MM YLW 5V RES QUAD TH |
| ASFLMPC-25.000MHZ-Z-T | OSC 25.000 MHZ CMOS MEMS SMD |
| 555-5009F | LED CBI 2MM RED 5V RES QUAD TH |
| P51-50-A-O-P-5V-000-000 | SENSOR 50PSI 7/16-20 UNF 2B 5V |
| P51-15-A-O-P-5V-000-000 | SENSOR 15PSI 7/16-20 UNF 2B 5V |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 11-01-0103 | 功能描述:折皱器 CRIMP HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 11-01-0105 | 功能描述:折皱器 PNEUMATIC HAND TOOL RoHS:否 制造商:Hirose Connector 类型: 描述/功能:Cable and Shield Crimper |
| 1101-01-0519 | 制造商:Concord Electronics Inc 功能描述:PTFE Insulated Terminal PIN 8.3mm 4.36mm Electro-Solder Over Copper |
| 11-01-0107 | 制造商:MOLEX 功能描述: |
| 11-01-0110 | 功能描述:手工工具 HAND TOOL-40682 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
发布紧急采购，3分钟左右您将得到回复。