参数资料
型号: 0638017200
厂商: Molex Inc
文件页数: 6/24页
文件大小: 0K
描述: CRMP PRESS TM3000 120V TO 10AWG
其它有关文件: Overlap Style Insulation Crimps
标准包装: 1
系列: TM-3000
工具类型: 台式压机,气动 - 无喷枪
适用于相关产品: FineAdjust? 和 Mini-Mac? 施用器
配用: 638027600-ND - MINI MAC APPLICATOR 14-16 AWG
638027500-ND - MINI MAC APPLICATOR 18-22 AWG
638027200-ND - MINI MAC APPLICATOR 14-18 AWG
638027100-ND - MINI MAC APPLICATOR 14-18 AWG
638027000-ND - MINI MAC APPLICATOR 14-18 AWG
638026900-ND - MINI MAC APPLICATOR 14-18 AWG
0639024800-ND - FINE ADJUST APPLICATOR
0639024700-ND - FINE ADJUST APPLICATOR
0639024600-ND - FINE ADJUST APPLICATOR
0639023900-ND - FINE ADJUST APPLICATOR
更多...
相关产品: WM5083-ND - GUARD TM-3000&4000 UNIV PRESS
WM5082-ND - TERMINAL OILER FOR TM-3000PRESS
WM6296-ND - TOOL PRESS SHUT HEIGHT GAUGE
其它名称: 063801-7200
063801-7200-E
0638017200-E
63801-7200
63801-7200-E
63801-7200-ND
638017200
638017200-E
WM4793
Quality Crimp Handbook
SECTION 4
DEFINITIONS
BEND UP
BRUSH
BELL
MOUTH
CONDUCTOR
CRIMP
SEAM
ROLLING
INSULATION
CRIMP
STRIP
LENGTH
CUT-OFF
TAB
CRIMP
BEND
DOWN
TWISTING
TERMINAL CROSS
SECTION VIEW
EXTRUSIONS
HEIGHT
EXTRUSION
Anatomy of a Crimp Termination (Figure 4-1)
Bell Mouth (Flare)
The flare that is formed on the edge of the
conductor crimp acts as a funnel for the wire
strands. This funnel reduces the possibility that a
sharp edge on the conductor crimp will cut or nick
the wire strands. As a general guideline, the
conductor bell mouth needs to be approximately 1
to 2 times the thickness of the terminal material. *
Bend Test
One way to test the insulation crimp is by bending
the wire several times and then evaluating the
movement of the insulation and wire strands. As a
rule, the insulation crimp should withstand the wire
being bent 60 to 90 degrees in any direction,
several times. Use care when working with small
wire sizes so the wire at the back of the insulation
crimp does not shear.
Conductor Brush
The conductor brush is made up of the wire strands
that extend past the conductor crimp on the contact
side of the terminal. This helps ensure that
EXTRUSION
Figure 4-1
mechanical compression occurs over the full length of
the conductor crimp. The conductor brush should not
extend into the contact area.
Conductor Crimp
This is the metallurgical compression of a terminal
around the wire's conductor. This connection creates a
common electrical path with low resistance and high
current carrying capabilities.
Conductor Crimp Height
The conductor crimp height is measured from the top
surface of the formed crimp to the bottom radial surface.
Do not include the extrusion points in this measurement
(See Figure 4-1). Measuring crimp height is a quick,
non-destructive way to help ensure the correct
metallurgical compression of a terminal around the
wire's conductor and is an excellent attribute for process
control. The crimp height specification is typically set as
a balance between electrical and mechanical
performance over the complete range of wire stranding
and coatings, and terminal materials and plating.
Although it is possible to optimize a crimp height to
individual wire stranding and terminal plating, one crimp
height specification is normally created.
*Consult individual terminal specification requirements
Order No: TM-638000029
Revision: D
Release Date: 09-04-03
Revision Date: 12-23-09
UNCONTROLLED COPY
Page 6 of 24
相关PDF资料
PDF描述
NDKR16H SW ROTARY DIP 8MM HEX RT ANG PC
MMA2260EGR2 SENSOR ACCEL X-AXIS 1.5G 16-SOIC
63811-8000 TOOL HAND CRIMP 22-28AWG
555-4003F LED 2MM QUAD 5V RED
555-4401F LED 2MM QUAD YELLOW
相关代理商/技术参数
参数描述
0638017205 功能描述:FACE PLATE 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1
0638017206 功能描述:SWITCH TDC 制造商:molex, llc 系列:* 零件状态:过期 标准包装:1
0638017207 功能描述:SWITCH W CABLE TDC 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1
0638017208 功能描述:ACCESS COVER 制造商:molex, llc 系列:* 零件状态:在售 标准包装:1
0638017211 制造商:Molex 功能描述:PROX SPLIT CYCLE 制造商:Molex 功能描述:PROX SPLIT CYCLE - Bulk 制造商:Molex 功能描述:PROX SPLIT CYCLE