参数资料
型号: XRT73LC03AIV
厂商: Exar Corporation
文件页数: 36/61页
文件大小: 0K
描述: IC LIU E3/DS3/STS-1 3CH 120LQFP
标准包装: 72
类型: 线路接口装置(LIU)
驱动器/接收器数: 3/3
规程: DS3,E3,STS-1
电源电压: 3.135 V ~ 3.465 V
安装类型: 表面贴装
封装/外壳: 120-LQFP
供应商设备封装: 120-LQFP(14x20)
包装: 托盘
XRT73LC03A
39
REV. 1.0.4
3 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
Decoder detects this particular pattern, then it substi-
tutes these bits with a “0000" pattern.
Figure 25 illustrates the HDB3 Decoder at work with
two separate Zero Suppression patterns, in the in-
coming Dual-Rail Data Stream.
NOTE: If the HDB3 Decoder detects any bipolar violation
(e.g., "V") pulses that is not in accordance with the HDB3
Line Code format, or if the HDB3 Decoder detects a string
of 4 (or more) "0's" in the incoming line signal, then the
HDB3 Decoder flags this event as a Line Code Violation by
pulsing the LCV output pin “High".
3.4.3
Configuring the HDB3/B3ZS Decoder
The XRT73LC03A can enable or disable the HDB3/
B3ZS Decoder blocks by either of the following
means.
a. Operating in the HOST Mode
Enable the HDB3/B3ZS Decoder block of Channel(n)
by writing a "0" into the (SR/DR)_(n) bit-field within
Command Register CR3-(n), as illustrated below.
b. Operating in the Hardware Mode
To globally enable all HDB3/B3ZS Decoder blocks in
the XRT73LC03A, pull the ENDECDIS input pin
“Low". To globally disable all HDB3/B3ZS Decoder
blocks in the XRT73LC03A and configure the
XRT73LC03A to transmit and receive in an AMI for-
mat, pull the ENDECDIS input pin "High".
3.5
LOS DECLARATION/CLEARANCE
Each channel of the XRT73LC03A contains circuitry
that monitors the following two parameters associat-
ed with the incoming line signals.
1. The amplitude of the incoming line signal via the
RTIP and RRing inputs.
2. The number of pulses detected in the incoming
line signal within a certain amount of time.
If a given channel of the XRT73LC03A determines
that the incoming line signal is missing due to either
insufficient amplitude or a lack of pulses in the incom-
ing line signal, it declares a Loss of Signal (LOS) con-
dition. The channel declares the LOS condition by
toggling its respective RLOS_(n) output pin “High”
and by setting its corresponding RLOS_(n) bit field in
Command Register 0 or Command Register 8 to "1".
Conversely, if the channel determines that the incom-
ing line signal has been restored (e.g., there is suffi-
cient amplitude and pulses in the incoming line sig-
nal), it clears the LOS condition by toggling its re-
spective RLOS_(n) output pin "Low" and setting its
corresponding RLOS_(n) bit-field to "0".
In general, the LOS Declaration/Clearance scheme
that is employed in the XRT73LC03A is based upon
FIGURE 25. AN EXAMPLE OF HDB3 DECODING
Data
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0 0
0
V
Line Signal
B
0 0
V
RPOS
RNEG
RCLK
COMMAND REGISTER CR2-(n)
D4
D3
D2
D1
D0
Reserved
ENDECDIS_(n)
ALOSDIS_(n)
DLOSDIS_(n)
REQEN_(n)
X
0X
X
1
相关PDF资料
PDF描述
MS3101A22-20S CONN RCPT 9POS FREE HNG W/SCKT
IDT72V263L10PFI8 IC FIFO 8192X18 10NS 80QFP
VI-B6B-IV-F1 CONVERTER MOD DC/DC 95V 150W
IDT72615L50PF8 IC FIFO BY SYNC 512X18X2 64QFP
MS27656T15F5PB CONN RCPT 5POS WALL MNT W/PINS
相关代理商/技术参数
参数描述
XRT73LC03AIVF 制造商:Exar Corporation 功能描述:Line Interface Unit 51.84Mbps DS3/E3/STS-1 Serial 120-Pin LQFP
XRT73LC03AIV-F 功能描述:外围驱动器与原件 - PCI 3-Ch DS3, E3, STS-1 RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray
XRT73LC04A 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04A_08 制造商:EXAR 制造商全称:EXAR 功能描述:4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
XRT73LC04AES 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流(最大值):595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray