- 您现在的位置：买卖IC网 > PDF目录16478 > ST16C2550CQ-0A-EB (Exar Corporation)EVAL BOARD FOR ST16C2550 PDF资料下载
参数资料
| 型号： | ST16C2550CQ-0A-EB |
| 厂商： | Exar Corporation |
| 文件页数： | 34/37页 |
| 文件大小： | 0K |
| 描述： | EVAL BOARD FOR ST16C2550 |
| 标准包装： | 1 |
| 系列： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页当前第34页第35页第36页第37页
ST16C2550
6
2.97V TO 5.5V DUART WITH 16-BYTE FIFO
REV. 4.4.1
NOTE: Pin type: I=Input, O=Output, IO= Input/output, OD=Output Open Drain.
CTSB#
25
28
23
I
UART channel B Clear-to-Send (active low) or general
purpose input. This input should be connected to VCC
when not used. This input has no effect on the UART.
DTRB#
34
38
35
O
UART channel B Data-Terminal-Ready (active low) or
general purpose output. If it is not used, leave it uncon-
nected.
DSRB#
22
25
20
I
UART channel B Data-Set-Ready (active low) or general
purpose input. This input should be connected to VCC
when not used. This input has no effect on the UART.
CDB#
19
21
16
I
UART channel B Carrier-Detect (active low) or general
purpose input. This input should be connected to VCC
when not used. This input has no effect on the UART.
RIB#
23
26
21
I
UART channel B Ring-Indicator (active low) or general
purpose input. This input should be connected to VCC
when not used. This input has no effect on the UART.
OP2B#
13
15
9
O
Output Port 2 Channel B - The output state is defined by
the user and through the software setting of MCR[3].
INTB is set to the active mode and OP2B# output to a
logic 0 when MCR[3] is set to a logic 1. INTB is set to the
three state mode and OP2B# to a logic 1 when MCR[3] is
set to a logic 0. See MCR[3]. This output should not be
used as a general output else it will disturb the INTB out-
put functionality. If it is not used, leave it unconnected.
ANCILLARY SIGNALS
XTAL1
16
18
13
I
Crystal or external clock input.
XTAL2
17
19
14
O
Crystal or buffered clock output.
RESET
35
39
36
I
Reset (active high) - A longer than 40 ns logic 1 pulse on
this pin will reset the internal registers and all outputs.
The UART transmitter output will be held at logic 1, the
receiver input will be ignored and outputs are reset during
reset period (see External Reset Conditions).
VCC
40
44
42
Pwr
2.97V to 5.5V power supply. All inputs are 5V tolerant for
devices with top marking of "A2 YYWW" and newer.
GND
20
22
17
Pwr
Power supply common, ground.
N.C.
-
12, 24, 25,
37
No Connection. These pins are open, but typically, should
be connected to GND for good design practice.
Pin Description
NAME
40-PDIP
PIN #
44-PLCC
PIN #
48-TQFP
PIN #
TYPE
DESCRIPTION
相关PDF资料 |
PDF描述 |
|---|---|
| LBC2518T331M | INDUCTOR WOUND 330UH 65MA 1007 |
| SP809EK-L-2-6/TR | IC MPU RESET CIRC 2.6V SOT23-3 |
| RBM15DTKI | CONN EDGECARD 30POS DIP .156 SLD |
| M1DXK-2040K | IDC CABLE - MKR20K/MC20F/X |
| L-14W2N0SV4E | WIREWOUND INDUCTOR 2NH 0603 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ST16C2550CQ-0B-EB | 功能描述:界面开发工具 Supports C2550 48 ld TQFP, PCI Interface RoHS:否 制造商:Bourns 产品:Evaluation Boards 类型:RS-485 工具用于评估:ADM3485E 接口类型:RS-485 工作电源电压:3.3 V |
| ST16C2550CQ48 | 制造商:Exar Corporation 功能描述: |
| ST16C2550CQ48-F | 功能描述:UART 接口集成电路 2.97V-5.5V 16B FIFO temp 0C to 70C; UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550CQ48TR-F | 功能描述:UART 接口集成电路 DUAL UART W/16BYTE FIFO RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| ST16C2550IJ44 | 制造商:Exar Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。