参数资料
型号: PR26MF21NSZF
厂商: Sharp Microelectronics
文件页数: 9/15页
文件大小: 0K
描述: RELAY SSR 120VAC .6A ZC 8-DIP
产品目录绘图: PRxxMF Series Circuit
标准包装: 50
系列: PR26MF
电路: SPST-NO(1 Form A)
输出类型: AC,过零
负载电流: 600mA
输入电压: 1.2VDC
电压 - 负载: 0 ~ 120 V
安装类型: 通孔
端接类型: PC 引脚
封装/外壳: 8-DIP(0.300",7.62mm),7 引线
供应商设备封装: 8-DIP
包装: 管件
继电器类型: 继电器
产品目录页面: 2634 (CN2011-ZH PDF)
其它名称: 425-2362-5
PR26MF21NSZ Series
PR36MF2xNSZ Series
■ Design Considerations
● Recommended Operating Conditions
Parameter
Symbol
Conditions
MIN.
MAX.
Unit
Input
Input signal current
at ON state
Rank 1
Rank 2
I F (ON)
?
20
10
25
15
mA
Input signal current at OFF state
I F (OFF)
?
0
0.1
mA
Load supply voltage
PR26MF21NSZ
PR36MF2xNSZ
V OUT (rms)
?
?
120
240
V
Output
Load supply current
I OUT (rms)
Locate snubber circuit between output terminals
(Cs = 0.022 μ F, Rs = 47 ? )
?
I T (rms) × 80%( ? )
mA
Frequency
Operating temperature
f
T opr
?
?
50
? 20
60
80
Hz
?C
( ? ) See Fig.2 about derating curve (I T (rms) vs. ambient temperature).
● Design guide
In order for the SSR to turn off, the triggering current (I F ) must be 0.1mA or less.
Particular attention needs to be paid when utilizing SSRs that incorporate zero crossing circuitry.
If the phase difference between the voltage and the current at the output pins is large enough, zero crossing
type SSRs cannot be used. The result, if zero crossing SSRs are used under this condition, is that the SSR
may not turn on and off irregardless of the input current. In this case, only a non zero cross type SSR should
be used in combination with the above mentioned snubber circuit selection process.
When the input current (I F ) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V D , increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs = 0.022 μ F and Rs = 47 ? . The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
For over voltage protection, a Varistor may be used.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
● Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
Sheet No.: D4-A00501EN
9
相关PDF资料
PDF描述
0395000602 3.5MM EURO PLUG RA BLK 2POS
PR36MF22NSZF RELAY SSR 240VAC .6A ZC 8-DIP
0395326503 5.08MM EURO HEADER RA GRN 3POS
0395325503 5.08MM EURO HEADER RA GRN 3POS
PR26MF11NIPF RELAY SSR 120VAC .6A 8-SMD
相关代理商/技术参数
参数描述
PR-26-REFLECTOR 功能描述:手工工具 REFLECTOR RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool
PR275A 制造商:RECTRON 制造商全称:Rectron Semiconductor 功能描述:SIDACTOR
PR28 制造商:VISUAL COMMUNICATIONS COMPANY LLC 功能描述:B-3 1/2 Miniature Flange Lamp
PR-28 制造商:B&K Precision Corporation 功能描述:
PR28A 制造商:B&K Precision Corporation 功能描述:High Voltage Multiplier Probe