- 您现在的位置：买卖IC网 > PDF目录18885 > NXFT15WF104FA2B050 (Murata Electronics North America)THERMO STRNG 100K OHM 1% PDF资料下载
参数资料
| 型号： | NXFT15WF104FA2B050 |
| 厂商： | Murata Electronics North America |
| 文件页数： | 31/44页 |
| 文件大小： | 0K |
| 描述： | THERMO STRNG 100K OHM 1% |
| 标准包装： | 1,000 |
| 在 25°C 时的电阻（欧姆）： | 100k |
| 电阻公差： | ±1% |
| B 值公差： | ±1% |
| B25/50： | 4250K |
| B25/85： | 4311K |
| B25/100： | 4334K |
| 工作温度： | -40°C ~ 125°C |
| 功率 - 最大： | 7.5mW |
| 长度 - 引线： | * |
| 安装类型： | 自由悬挂 |
| 封装/外壳： | 磁珠 |
| 包装： | 散装 |
| 其它名称： | 490-5632 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
! Note ? Please read rating and ! CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
? This catalog has only typical speci?cations. Therefore, please approve our product speci?cations or transact the approval sheet for product speci?cations before ordering.
R44E.pdf
Dec.17,2012
Temperature Sensor Lead Type Speci?cations and Test Methods
No.
1
2
3
4
5
Item
Low Temperature
Storage Test
High Temperature
Storage Test
High Temperature
Load
Humidity Storage
Test
Temperature
Cycle
Specifications
· Resistance (R25°C) fluctuation rate: less than ±1%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
· Resistance (R25°C) fluctuation rate: less than ±2%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
Test Methods
-40 +0/-3°C in air, for 1000 +48/-0 hours without loading.
125±2°C in air, for 1000 +48/-0 hours without loading.
85±2°C in air, with ‘Operating Current for Sensor’ for
1000 +48/-0 hrs.
60±2°C, 90 to 95%RH in air, for 1000 +48/-0 hours without
loading.
-40°C +0/-3°C, 30 minutes in air
+25°C±2°C, 10 to 15 minutes in air
+125°C +3/-0°C, 30 minutes in air
+25°C +2/-0°C, 10 to 15 minutes in air (1 cycle)
Continuous 100 cycles, without loading.
6
Insulation Break -
down Voltage
· No damage electrical characteristics on D.C.100 V, 1 min.
2mm length of coating resin from the top of thermistor is to be
dipped into beads of lead (Pb), and DC100V 1 minute is
applied to circuit between beads of lead (Pb) and lead wire.
Both lead wires are dipped into 350±10°C solder for 3.5±0.5
seconds, or 260±5°C solder for 10±1 seconds according to
Fig-1. (solder <Sn-3Ag-0.5Cu>)
7
Resistance to
Soldering Heat
· Resistance (R25°C) fluctuation rate: less than ±1%.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
Solder
Fig-1
Both lead wires are dipped into flux (25wt% colophony
8
Solder Ability
· More than 90% of lead wire surface shall be covered by
solder.
<JIS K 5902> isopropyl alcohol <JIS K 8839>) for 5 to 10
seconds. Then both lead wires are dipped into 245±5°C solder
<Sn-3Ag-0.5Cu> for 2±0.5 seconds according to Fig-1.
One end of a lead wire shall be fixed and 2.5N forth for 10
seconds shall be applied to the other lead wire as shown in
Fig-2.
6
9
Lead Wire Pull
Strength
· Resistance(R25°C) fluctuation rate: less than ±1%.
· B-Constant(B25/50°C) fluctuation rate: less than ±1%.
· No visible damage at resin part.
2.5N (10sec.)
Fig-2
One lead wire is held and 2.5N force is applied. Then the body
of NTC thermistor is bent by 90°C and again bent back to the
initial position. This sequence shall be completed twice. See
Fig-3.
10
Lead Wire
Bending Strength
· Lead wire does not break.
90°
2.5N
Fig-3
11 Free Fall
· Resistance (R25°C) fluctuation rate: less than ±1%.
NTC thermistor shall be dropped without any force onto
concrete floor from 1 meter height one time.
· B-Constant (B25/50°C) fluctuation rate: less than ±1%.
NTC thermistor shall be fixed to the vibration test Equipment.
12 Vibration
· No visible damage at resin part.
Vibration of total 1.5mm amplitude, Frequency sequence of
10Hz – 55Hz – 10Hz in 1 minute, shall be applied for right
angled 3 directions for each 2 hours duration.
* · R25 is zero-power resistance at 25°C.
· B25/50 is calculated by zero-power resistance of Thermistor in 25°C-50°C.
· After each test, NTC Thermistor should be kept for 1 hour at room temperature (normal humidity and normal atmospheric pressure).
29
相关PDF资料 |
PDF描述 |
|---|---|
| 2390QD5-28V | INDICATOR NEON GREEN PANEL MNT |
| ASEMB-60.000MHZ-XY-T | OSC MEMS 60.000 MHZ SMD |
| 2390QD4-28V | INDICATOR NEON WHITE PANEL MNT |
| 2390QD3-28V | INDICATOR NEON AMBER PANEL MNT |
| 2191LX1-12V | LED IND LGT 12V RED W/BLK BEZEL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| NXFT15WF104FA2B060 | 功能描述:热敏电阻 - NTC 0402 100k ohm+/-1% 4250K+/-1% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NXFT15WF104FA2B070 | 功能描述:热敏电阻 - NTC 0402 100k ohm+/-1% 4250K+/-1% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NXFT15WF104FA2B080 | 功能描述:热敏电阻 - NTC 0402 100k ohm+/-1% 4250K+/-1% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NXFT15WF104FA2B090 | 功能描述:热敏电阻 - NTC 0402 100k ohm+/-1% 4250K+/-1% RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
| NXFT15WF104FA2B100 | 功能描述:热敏电阻 - NTC 100Kohm +/-1% 4250K 100mm length RoHS:否 制造商:EPCOS 电阻:10 kOhms 功率额定值:150 mW 容差:2 % 端接类型:Radial 系列:B57703M 工作温度范围:- 55 C to + 125 C |
发布紧急采购，3分钟左右您将得到回复。