参数资料
| 型号： | MV036F120M010 |
| 厂商： | Vicor Corporation |
| 文件页数： | 6/10页 |
| 文件大小： | 0K |
| 描述： | TRANSFORMER/CONVERT 12V 10A SMD |
| 应用说明： | Factorized Power Architecture and V-I Chips |
| 产品培训模块： | VI Chip PRM and VTM Factorized Power Architecture |
| 标准包装： | 1 |
| 系列： | V-I Chip™, VTM™ |
| 类型： | 变压模块 |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 26V |
| 电压 - 输入（最大）： | 50V |
| 输出电压： | 12V |
| 电流 - 输出（最大）： | 10A |
| 电源（瓦） - 制造商系列： | 120W |
| 电压 - 隔离： | 2.25kV（2250V） |
| 应用： | 商用 |
| 特点： | 具有远程开/关功能 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 模块 |
| 尺寸/尺寸： | 1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） |
| 包装： | 托盘 |
| 工作温度： | -55°C ~ 125°C |
| 效率： | 95.5% |
| 电源（瓦特）- 最大： | 120W |
| 重量： | 0.033 磅（14.97g） |
| 配用： | 1102-1000-ND - EVAL BRD V.I CHIP VTM CUR MULT |
| 其它名称： | 1102-1007 |
Not Recommended for New Designs / End of Life - Please see First Page
+In / -In DC Voltage Ports
MV036 SERIES
The VTM ? input should be connected to the PRM ? output terminals.
4
3
2
1
Given that both the PRM and VTM have high switching frequencies, it
is often good practice to use a series inductor to limit high frequency
currents between the PRM output and VTM input capacitors. The input
voltage should not exceed the maximum specified. If the input voltage
exceeds the overvoltage turn-off, the VTM will shutdown. The VTM
does not have internal input reverse polarity protection. Adding a
properly sized diode in series with the positive input or a fused reverse-
shunt diode will provide reverse polarity protection.
+Out
-Out
+Out
A
B
C
D
E
F
G
H
J
K
L
A
B
C
D
E
H
J
K
L
+In
TM
VC
PC
M
M
TM – For Factory Use Only
-Out
N
P
R
T
N
P
R
T
-In
VC – VTM Control
The VC port is multiplexed. It receives the initial V CC voltage from an
upstream PRM, synchronizing the output rise of the VTM with the
output rise of the PRM. Additionally, the VC port provides feedback to
Bottom View
the PRM to compensate for the VTM output resistance. In typical
applications using VTMs powered from PRMs, the PRM’s VC port
should be connected to the VTM VC port.
The VC port is not intended to be used to supply V CC voltage to the
VTM for extended periods of time. If VC is being supplied from a source
other than the PRM, the voltage should be removed after 20 ms.
PC – Primary Control
The Primary Control (PC) port is a multifunction port for controlling the
VTM as follows:
Disable – If PC is left floating, the VTM output is enabled. To
disable the output, the PC port must be pulled lower than 2.4 V,
referenced to -In. Optocouplers, open collector transistors or relays
can be used to control the PC port. Once disabled, 14 V must be
re-applied to the VC port to restart the VTM.
Primary Auxiliary Supply – The PC port can source up to 2.4 mA
at 5 Vdc.
+Out / -Out DC Voltage Output Ports
The output and output return are through two sets of contact
locations. The respective +Out and –Out groups must be connected in
parallel with as low an interconnect resistance as possible.
To take full advantage of the VTM, the user should note the low output
impedance of the device. The low output impedance provides fast
transient response without the need for bulk POL capacitance. Limited-
life electrolytic capacitors required with conventional converters can be
reduced or even eliminated, saving cost and valuable board real estate.
Signal Name
+In
–In
TM
VC
PC
+Out
–Out
Figure 9 — VTM pin configuration
Pin Designation
A1-E1, A2-E2
L1-T1, L2-T2
H1, H2
J1, J2
K1, K2
A3-D3, A4-D4,
J3-M3, J4-M4
E3-H3, E4-H4,
N3-T3, N4-T4
MIL-COTS Chip Transformer
Page 6 of 10
Rev 2.9
01/2014
vicorpower.com
800 927.9474
相关PDF资料 |
PDF描述 |
|---|---|
| MS3452L32-7A | CONN HSG RCPT 35POS BOX MNT PINS |
| MV036F045M027 | TRANSFORMER/CONVERT 4.5V 27A SMD |
| D38999/24MA98BN | CONN HSG RCPT 3POS JAM NUT SCKT |
| BCM352T125T300A00 | HV BCM BUS CONVERT 12.5V 300W |
| MS27497E22B35SDLC | CONN HSG RCPT 100POS WALL MT SKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MV036F120M010_10 | 制造商:VICOR 制造商全称:Vicor Corporation 功能描述:Transformer |
| MV036F120M010-CB | 功能描述:EVAL BRD V.I CHIP VTM CUR MULT RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, VTM™ 标准包装:1 系列:- 主要目的:DC/DC，步降 输出及类型:1，非隔离 功率 - 输出:- 输出电压:3.3V 电流 - 输出:3A 输入电压:4.5 V ~ 28 V 稳压器拓扑结构:降压 频率 - 开关:250kHz 板类型:完全填充 已供物品:板 已用 IC / 零件:L7981 其它名称:497-12113STEVAL-ISA094V1-ND |
| MV036F180M007 | 功能描述:MIL-COTS VTM CURRENT MULTIPLIER RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
| MV036F180M007-CB | 功能描述:VTM CURRENT MULTIPLIER EVAL BOAR RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:V-I Chip™, VTM™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| MV036F240M005 | 功能描述:MIL-COTS VTM CURRENT MULTIPLIER RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g） |
发布紧急采购，3分钟左右您将得到回复。