- 您现在的位置：买卖IC网 > PDF目录13175 > MIC2776N-BM5 TR (Micrel Inc)IC SUPERVISOR ADJ MCRPWR SOT23-5 PDF资料下载
参数资料
| 型号： | MIC2776N-BM5 TR |
| 厂商： | Micrel Inc |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | IC SUPERVISOR ADJ MCRPWR SOT23-5 |
| 标准包装： | 3,000 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 可调节/可选择 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SC-74A，SOT-753 |
| 供应商设备封装： | SOT-23-5 |
| 包装： | 带卷 (TR) |
| 其它名称： | MIC2776N-BM5TR |
( R1 + R2 )
V TH = V REF ×
( R TOTAL ) ( V REF )
V TH
V CORE(min) 0.950
1.025
1.025
MIC2776
Application Information
Programming the Voltage Threshold
Referring to the “Typical Application Circuit”, the voltage
threshold is calculated as follows:
R2
where V REF = 0.300V
In order to provide the additional criteria needed to solve
for the resistor values, the resistors can be selected such
that the two resistors have a given total value, that is, R1
+ R2 = R TOTAL . Imposing this condition on the resistor val-
ues provides two equations that can be solved for the two
unknown resistor values. A value such as 1MΩ for R TOTAL
is a reasonable choice since it keeps quiescent current to a
generally acceptable level while not causing any measurable
errors due to input bias currents. The larger the resistors, the
larger the potential errors due to input bias current (I IN ). The
maximum recommended value of R TOTAL is 3MΩ.
Applying this criteria and rearranging the V TH expression to
solve for the resistor values gives:
R2 =
R1 = R TOTAL – R2
Application Example
Figure 1 below illustrates a hypothetical MIC2776 application
in which the MIC2776 is used to monitor the core supply of a
high-performance CPU or DSP. The core supply, V CORE , in
this example is 1.0V ±5%. The main power rail and I/O volt-
age, V I/O , is 2.5V ±5%. As shown in Figure 1, the MIC2776
is powered by V I/O . The minimum value of V I/O is 2.5V –5%
= 2.375V; the maximum is 2.5V +5% = 2.625V. This is well
within the MIC2776’s power supply range of 1.5V to 5.5V.
Resistors R1 and R2 must be selected to correspond to the
V CORE supply of 1.0V. The goal is to insure that the core supply
voltage is adequate to insure proper operation, i.e., V CORE
≥ (1.0V –5%) = 0.950V. Because there is always a small
degree of uncertainty due to the accuracy of the resistors,
variations in the devices’ voltage reference, etc., the threshold
will be set slightly below this value. The potential variation in
the MIC2776’s voltage reference is speci?ed as ±1.5%. The
resistors chosen will have their own tolerance speci?cation.
This example will assume the use of 1% accurate resistors.
The potential worst-case error contribution due to input bias
current can be calculated once the resistor values are chosen.
If the guidelines above regarding the maximum total value of
R1+R2 are followed, this error contribution will be very small
thanks to the MIC2776’s very low input bias current.
Micrel, Inc
To summarize, the various potential error sources are:
? Variation in V REF : speci?ed at ±1.5%
? Resistor tolerance:
chosen by designer (typically ≤ ±1%)
? Input bias current, I IN :
calculated once resistor values are known, typically
very small
Taking the various potential error sources into account, the
threshold voltage will be set slightly below the minimum V CORE
speci?cation of 0.950V so that when the actual threshold
voltage is at its maximum, it will not intrude into the normal
operating range of V CORE . The target threshold voltage will
be set as follows:
Given that the total tolerance on V TH is [V REF tolerance] +
[resistor tolerance]
= ±1.5% + ±1% = ±2.5%,
and V TH(max) = V CORE(min) ,
then V CORE(min) = V TH + 2.5% V TH = 1.025 V TH ,
therefore, solving for V TH results in
V TH = = = 0.9268V
Solving for R1 and R2 using this value for V TH and the equa-
tions above yields:
R1 = 676.3kΩ ≈ 673kΩ
R2 = 323.7kΩ ≈ 324kΩ
The resulting circuit is shown in Figure 1.
Input Bias Current Effects
Now that the resistor values are known, it is possible to cal-
culate the maximum potential error due to input bias current,
I IN . As shown in the “Electrical Characteristics” table, the
maximum value of I IN is 10nA. (Note that the typical value
is a much smaller 5pA!) The magnitude of the offset caused
by I IN is given by:
V ERROR = I IN(max) × (R1||R2) =
V ERROR = ±1 × 10 -8 A × 2.189 ×10 5 ? =
V ERROR = ±2.189 × 10 -3 V =
V ERROR = ±2.189mV
The typical error is about three orders of magnitude lower
than this - close to one microvolt! Generally, the error
due to input bias can be discounted. If it is to be taken
into account, simply adjust the target threshold voltage
downward by this amount and recalculate R1 and R2. The
resulting value will be very close to optimum. If accuracy
is more important than the quiescent current in the
resistors, simply reduce the value of R TOTAL to minimize
offset errors.
MIC2776
6
November 2005
相关PDF资料 |
PDF描述 |
|---|---|
| EL7640ILTZ-T7 | CONV DC/DC TFT-LCD 32-QFN |
| UWT1H221MNR1GS | CAP ALUM 220UF 50V 20% SMD |
| EGM31DRMN-S288 | CONN EDGECARD 62POS .156 EXTEND |
| MIC2774N-31BM5 TR | IC SUPERVISOR DUAL 3.09 SOT23-5 |
| 200VXH330MEFCSN22X25 | CAP ALUM 330UF 200V 20% SNAP-IN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MIC2776N-BM5TX | 制造商:RF Micro Devices Inc 功能描述: |
| MIC2776NYM5 | 制造商:Micrel Inc 功能描述: |
| MIC2776N-YM5 | 制造商:Rochester Electronics LLC 功能描述: 制造商:RF Micro Devices Inc 功能描述: 制造商:Micrel Inc 功能描述: |
| MIC2776N-YM5 TR | 功能描述:监控电路 Adjustable Voltage Supervisor with 0.3V Threshold, Manual Reset and Active-Low Open-Drain Output in SOT23-5 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel |
| MIC2776N-YM5TR | 制造商:Micrel 功能描述:Volt Supervisor Supply Micropower |
发布紧急采购，3分钟左右您将得到回复。