- 您现在的位置：买卖IC网 > PDF目录5136 > MAX8795AGCJ+T (Maxim Integrated Products)IC CONV DC-DC TFT-LCD 32LQFP PDF资料下载
参数资料
| 型号： | MAX8795AGCJ+T |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 23/31页 |
| 文件大小： | 0K |
| 描述： | IC CONV DC-DC TFT-LCD 32LQFP |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,000 |
| 应用： | 转换器，TFT，LCD |
| 输入电压： | 2.5 V ~ 6 V |
| 输出数： | 8 |
| 输出电压： | 2.5 V ~ 18 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-LQFP |
| 供应商设备封装： | 32-LQFP（7x7） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页
TFT-LCD DC-DC Converter with
Operational Amplifiers
I LOAD ( MAX ) = ? I DRV ? BE ? × h FE ( MIN )
Charge-Pump Output Capacitor
Increasing the output capacitance or decreasing the
ESR reduces the output ripple voltage and the peak-to-
peak transient voltage. With ceramic capacitors, the
output voltage ripple is dominated by the capacitance
value. Use the following equation to approximate the
required capacitor value:
voltage, and power dissipation. The transistor’s current
gain limits the guaranteed maximum output current to:
? V ?
? R BE ?
where I DRV is the minimum guaranteed base-drive cur-
C OUT _ CP ≥
I LOAD _ CP
2 f OSC V RIPPLE _ CP
rent, V BE is the transistor’s base-to-emitter forward volt-
age drop, and R BE is the pullup resistor connected
between the transistor’s base and emitter. Furthermore,
the transistor’s current gain increases the linear regula-
R 4 = R 5 × ? GON ? 1 ?
R 7 = R 8 × FBN GOFF
? I BIAS FE ? ?
× h
A V _ LR ? ? V T ? × ? 1 + ? I ? ? × V REF
where C OUT_CP is the output capacitor of the charge
pump, I LOAD_CP is the load current of the charge
pump, and V RIPPLE_CP is the peak-to-peak value of the
output ripple.
Charge-Pump Rectifier Diodes
Use low-cost silicon switching diodes with a current rat-
ing equal to or greater than two times the average
charge-pump input current. If it helps avoid an extra
stage, some or all of the diodes can be replaced with
Schottky diodes with an equivalent current rating.
Linear-Regulator Controllers
Output-Voltage Selection
Adjust the gate-on linear-regulator (REG P) output volt-
age by connecting a resistive voltage-divider from the
REG P output to AGND with the center tap connected
to FBP (Figure 1). Select the lower resistor of the divider
R5 in the range of 10k ? to 30k ? . Calculate the upper
resistor R4 with the following equation:
? V ?
? V FBP ?
where V FBP = 1.25V (typ).
Adjust the gate-off linear-regulator REG N output volt-
age by connecting a resistive voltage-divider from
V GOFF to REF with the center tap connected to FBN
(Figure 1). Select R8 in the 20k ? to 50k ? range.
Calculate R7 with the following equation:
V ? V
V REF ? V FBN
where V FBN = 250mV, V REF = 1.25V. Note that REF can
only source up to 50μA; using a resistor less than 20k ?
for R8 results in higher bias current than REF can supply.
Pass-Transistor Selection
The pass transistor must meet specifications for current
gain (h FE ), input capacitance, collector-emitter saturation
tor’s DC loop gain (see the Stability Requirements sec-
tion), so excessive gain destabilizes the output.
Therefore, transistors with current gain over 100 at the
maximum output current can be difficult to stabilize and
are not recommended unless the high gain is needed to
meet the load-current requirements.
The transistor’s saturation voltage at the maximum out-
put current determines the minimum input-to-output
voltage differential that the linear regulator can support.
Also, the package’s power dissipation limits the usable
maximum input-to-output voltage differential. The maxi-
mum power-dissipation capability of the transistor’s
package and mounting must exceed the actual power
dissipated in the device. The power dissipated equals
the maximum load current (I LOAD(MAX)_LR ) multiplied
by the maximum input-to-output voltage differential:
P = I LOAD ( MAX )_ LR × ( V IN ( MAX )_ LR ? V OUT _ LR )
where V IN(MAX)_LR is the maximum input voltage of the
linear regulator, and V OUT _ LR is the output voltage of
the linear regulator.
Stability Requirements
The MAX8795A linear-regulator controllers use an inter-
nal transconductance amplifier to drive an external
pass transistor. The transconductance amplifier, the
pass transistor, the base-emitter resistor, and the out-
put capacitor determine the loop stability. The following
applies to both linear-regulator controllers in the
MAX8795A.
The transconductance amplifier regulates the output
voltage by controlling the pass transistor’s base cur-
rent. The total DC loop gain is approximately:
? 10 ? ?
? ?
? ? LOAD _ LR ? ?
where V T is 26mV at room temperature, and I BIAS is the
current through the base-to-emitter resistor (R BE ). For
the MAX8795A, the bias currents for both the gate-on
______________________________________________________________________________________
23
相关PDF资料 |
PDF描述 |
|---|---|
| MAX606ESA+ | IC DC-DC CONVERT 8-SOIC |
| RBC18DRSD-S273 | CONN EDGECARD 36POS DIP .100 SLD |
| X40430S14-C | IC VOLT MON TRPL EEPROM 14-SOIC |
| X40430S14-BT1 | IC VOLT MON TRPL EEPROM 14-SOIC |
| X40430S14-B | IC VOLT MON TRPL EEPROM 14-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX8796GTJ+ | 功能描述:电压模式 PWM 控制器 IMVP6 Single-Phase PWM Controller RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| MAX8796GTJ+C8V | 制造商:Maxim Integrated Products 功能描述:IMVP6/GMCH CONTROLLER - Rail/Tube |
| MAX8796GTJ+G05 | 制造商:Maxim Integrated Products 功能描述:IMVP6/GMCH CONTROLLER - Rail/Tube |
| MAX8796GTJ+G071 | 制造商:Maxim Integrated Products 功能描述:IMVP6/GMCH CONTROLLER - Rail/Tube |
| MAX8796GTJ+G1D | 功能描述:电压模式 PWM 控制器 1-Phase Quick-PWM Intel IMVP-6/GMCH RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。