- 您现在的位置：买卖IC网 > PDF目录15487 > MAX1639ESE+ (Maxim Integrated Products)IC REG CTRLR BUCK PWM CM 16-SOIC PDF资料下载
参数资料
| 型号： | MAX1639ESE+ |
| 厂商： | Maxim Integrated Products |
| 文件页数： | 13/13页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM CM 16-SOIC |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 50 |
| PWM 型： | 电流模式 |
| 输出数： | 1 |
| 频率 - 最大： | 1.2MHz |
| 占空比： | 84% |
| 电源电压： | 4.5 V ~ 5.5 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 16-SOIC（0.154"，3.90mm 宽） |
| 包装： | 管件 |
High-Speed Step-Down Controller with
Synchronous Rectification for CPU Power
large power diodes, such as the 1N4001 or 1N5817.
Exercise caution in the selection of Schottky diodes,
since some types exhibit high reverse leakage at high
operating temperatures. Bypass BST to LX using a
0.1μF capacitor.
Selecting the Input Capacitors
Place a 0.1μF ceramic capacitor and 10μF capacitor
between V CC and AGND, as well as between V DD and
PGND, within 0.2 in. (5mm) of the V CC and V DD pins.
Select low-ESR input filter capacitors with a ripple-
current rating exceeding the RMS input ripple current,
connecting several capacitors in parallel if necessary.
RMS input ripple current is determined by the input
voltage and load current, with the worst-possible case
occurring at V IN = 2 x V OUT :
Place the high-power components (C1, R1, N1, D1, N2,
L1, and C2 in Figure 1) as close together as possible.
Minimize ground-trace lengths in high-current paths.
The surface-mount power components should be
butted up to one another with their ground terminals
almost touching. Connect their ground terminals using
a wide, filled zone of top-layer copper (the pseudo-
ground plane), rather than through the internal ground
plane. At the output terminal, use vias to connect the
top-layer pseudo-ground plane to the normal inner-
layer ground plane at the output filter capacitor ground
terminals. This minimizes interference from IR drops
and ground noise, and ensures that the IC’s AGND is
sensing at the supply’s output terminals.
Minimize high-current path trace lengths. Use very
short and wide traces. From C1 to N1: 0.4 in. (10mm)
I RMS = I LOAD ( MAX )
V IN
V OUT ( V IN ? V OUT )
max length; D1 anode to N2: 0.2 in. (5mm) max length;
LX node (N1 source, N2 drain, D1 cathode, inductor
L1): 0.6 in. (15mm) max length.
I RMS = I OUT / 2 when V IN = 2 V OUT
__________Applications Information
Efficiency Considerations
___________________Pin Configuration
TOP VIEW
Refer to the MAX796–MAX799 data sheet for informa-
tion on calculating losses and improving efficiency.
BST 1
PWROK 2
16 DH
15 LX
PC Board Layout Considerations
Good PC board layout and routing are required in high-
current, high-frequency switching power supplies to
achieve good regulation, high efficiency, and stability.
The PC board layout artist must be provided with explicit
instructions concerning the placement of power-switch-
ing components and high-current routing. It is strongly
CSL 3
CSH 4
V CC 5
REF 6
AGND 7
MAX1639
14 PGND
13 DL
12 V DD
11 FREQ
10 CC2
recommended that the evaluation kit PC board layouts
FB 8
9
CC1
be followed as closely as possible. Contact Maxim’s
Applications Department concerning the availability of
PC board examples for higher-current circuits.
In most applications, the circuit is on a multilayer
board, and full use of the four or more copper layers is
recommended. Use the top layer for high-current
power and ground connections. Leave the extra cop-
per on the board as a pseudo-ground plane. Use the
bottom layer for quiet connections (REF, FB, AGND),
and the inner layers for an uninterrupted ground plane.
A ground plane and pseudo-ground plane are essential
for reducing ground bounce and switching noise.
A "+" SIGN WILL REPLACE THE FIRST PIN INDICATOR ON LEAD-FREE PACKAGES.
___________________Chip Information
TRANSISTOR COUNT: 3135
SUBSTRATE CONNECTED TO AGND
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
13 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
? 2005 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
相关PDF资料 |
PDF描述 |
|---|---|
| MAX776ESA+ | IC REG CTRLR INV PWM 8-SOIC |
| MAX5069DAUE+ | IC REG CTRLR ISO PWM CM 16-TSSOP |
| MAX1745AUB+ | IC REG CTRLR BUCK PWM 10-UMAX |
| SPD74-684M | INDUCTOR SHIELDED 680.0UH SMD |
| SPD74-683M | INDUCTOR SHIELDED 68.0UH SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| MAX1639ESE+ | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639ESE+T | 功能描述:DC/DC 开关控制器 High Speed Step Down RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639ESE-T | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX1639EVKIT | 功能描述:DC/DC 开关控制器 Evaluation Kit the MAX1639 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| MAX163BCNG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。