- 您现在的位置：买卖IC网 > PDF目录17168 > LTC1559CGN-5#PBF (Linear Technology)IC BACKUP BATT CNTRLR 5V 16-SSOP PDF资料下载
参数资料
| 型号： | LTC1559CGN-5#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/20页 |
| 文件大小： | 0K |
| 描述： | IC BACKUP BATT CNTRLR 5V 16-SSOP |
| 标准包装： | 100 |
| 功能： | 备份管理 |
| 电池化学： | 镍镉 |
| 电源电压： | 4.4 V ~ 5.5 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 16-SSOP |
| 包装： | 管件 |
LTC1559-3.3/LTC1559-5
APPLICATIO N S I N FOR M ATIO N
example, a small 60mAhr SAFT cell can back up the
system for 20 minutes at an output power of 100mW. Note
that at V CC = 3.07V (LTC1559-3.3), the boost converter
efficiency improves and allows more backup time from the
same cell compared to V CC = 4.625V (LTC1559-5).
Once it reaches full recharge, a cell bigger than 512mAhr
will overrun the gas gauge counter before it runs out of
charge during an extended backup cycle. The LTC1559
gas gauge counter will not roll over if this occurs; it will
stay at full count until the backup cycle ends and then
partially recharge the cell with a full count cycle as above.
Very short backup cycles (< 32s) may not extract enough
charge from the backup cell to increment the gas gauge
counter at all. To ensure that the backup cell is not slowly
“nibbled” away, the gas gauge counter is always
incremented by 1mAhr each time the controller exits
backup. This ensures that the backup cell is replenished
with at least a 1mAhr charge every time the LTC1559
enters backup mode.
Battery Backup Cell Trickle Charge
When the gas gauge counter reaches zero, the LTC1559
terminates fast recharge and reduces the recharge current
to the user-programmed trickle current level. The LTC1559
provides a trickle current that the user can program from
50 μ A to 2mA. The trickle current is set by an external
resistor from the positive terminal of the backup cell to the
V CC
CTL pin. In trickle charge mode, CTL is regulated to 0.5V,
resulting in a CTL pin current of (V BAT – 0.5)/R EXT . This
current is internally multiplied to feed back ten times the
R EXT current into the backup battery. Since the LTC1559
trickle charges only after the completion of the fast
recharge cycle, the backup cell voltage should be very
close to 1.2V. This simplifies the calculation of the R EXT
resistor value. For example, a 47k resistor from V BAT to
CTL sets the trickle charge current to 150 μ A.
Undervoltage Lockout
The LTC1559 includes an undervoltage lockout (UVLO)
circuit that shuts the system down gracefully if the backup
cell is exhausted or overloaded. As described in the
previous section, the LTC1559 terminates backup opera-
tion and remains off until the main power supply returns.
It then runs a fast recharge cycle to recharge the backup
cell. An onboard low-battery comparator in the 16-pin GN
or SO package provides an early warning signal if the
backup cell drops below 1V.
The UVLO circuit trips if the LTC1559’s V CC supervisory
circuit detects that V CC drops below – 9% of the rated V CC
voltage due to overload or output short-circuit conditions.
Once the UVLO circuit trips, the LTC1559 asserts the
RESET and RESET pins until the V CC voltage drops below
1V. It then remains off until V CC rises to within – 5.5% of
the rated output voltage (LTC1559-3.3). During power-up
from UVLO, the LTC1559 asserts the RESET and RESET
pins until the V C C ( r a t e d v a l u e ) – 5.5% (LTC1559-3.3)
threshold. Once V CC exceeds V C C ( r a t e d v a l u e ) – 5.5%
10I
SW
(LTC1559-3.3), the RESET and RESET pins remain
asserted for another 200ms (“hard” reset) before being
1.2V
NiCd
CELL
+
1 μ F
I
released to inform the system to start operating.
R EXT
CTL
Reset Operation
The LTC1559 includes an onboard push-button reset
–
+
1 ×
11 ×
switch controller. If the CTL pin is pulled to ground
(< 250mV) by a push-button or an open-drain output, the
LTC1559 generates a pulse at the RESET and RESET pins
after the trailing edge of the CTL signal. A short (less than
–
+
0.5V
LTC1559
two seconds) low going signal at CTL generates a “soft”
reset (100 μ s) pulse at the reset pins. A low CTL signal for
Figure 4. Trickle Current Charger
1559 F04
more than two seconds generates a “hard” reset pulse at
the RESET and RESET pins. During “hard” reset, the
13
相关PDF资料 |
PDF描述 |
|---|---|
| RNM-3.312S | CONV DC/DC 1W 3.3VIN 12VOUT |
| RCC22DRTN | CONN EDGECARD 44POS DIP .100 SLD |
| RNM-3.309S | CONV DC/DC 1W 3.3VIN 09VOUT |
| LTC1558CS8-5#PBF | IC BACKUP BATT CONTRLR 5V 8-SOIC |
| 0210490708 | CABLE JUMPER 1.25MM .127M 4POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC1559CS-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1559CS-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
| LTC1559CS-5 | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:61 系列:- 功能:电源管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:4.35 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:22-WFDFN 裸露焊盘 供应商设备封装:22-DFN（6x3）裸露焊盘 包装:管件 |
| LTC1559CS-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 标准包装:1 系列:- 功能:充电管理 电池化学:锂离子（Li-Ion）、锂聚合物（Li-Pol） 电源电压:3.75 V ~ 6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:剪切带 (CT) 产品目录页面:669 (CN2011-ZH PDF) 其它名称:MCP73831T-2ACI/OTCT |
发布紧急采购，3分钟左右您将得到回复。