- 您现在的位置：买卖IC网 > PDF目录14462 > LT3971IMSE16#PBF (Linear Technology)IC REG BUCK ADJ 1.2A 16MSOP PDF资料下载
参数资料
| 型号： | LT3971IMSE16#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 16MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.19 V ~ 30 V |
| 输入电压： | 4.3 V ~ 38 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3971/LT3971-3.3/LT3971-5
APPLICATIONS INFORMATION
R1 = R2 ? OUT ? 1 ?
5μs/DIV
feedbackresistorsandalowleakageSchottkycatchdiode
in applications utilizing the ultralow quiescent current
performance of the LT3971. The feedback resistors should
preferably be on the order of MΩ and the Schottky catch
diode should have less than 1μA of typical reverse leak-
age at room temperature. These two considerations are
reiterated in the FB Resistor Network and Catch Diode
Selection sections.
It is important to note that another way to decrease the
pulse frequency is to increase the magnitude of each
single current pulse. However, this increases the output
voltage ripple because each cycle delivers more power to
the output capacitor. The magnitude of the current pulses
was selected to ensure less than 15mV of output ripple in
a typical application. See Figure 2.
V SW
5V/DIV
I L
500mA/DIV
V OUT
20mV/DIV
3971 F02
V IN = 12V
V OUT = 3.3V
I LOAD = 10mA
Figure 2. Burst Mode Operation
While in Burst Mode operation, the burst frequency and
the charge delivered with each pulse will not change with
output capacitance. Therefore, the output voltage ripple
will be inversely proportional to the output capacitance.
In a typical application with a 22μF output capacitor, the
output ripple is about 10mV, and with a 47μF output ca-
pacitor the output ripple is about 5mV. The output voltage
ripple can continue to be decreased by increasing the
output capacitance.
At higher output loads (above 92mA for the front page
application) the LT3971 will be running at the frequency
programmed by the R T resistor, and will be operating in
standard PWM mode. The transition between PWM and low
ripple Burst Mode operation will exhibit slight frequency
jitter, but will not disturb the output voltage.
To ensure proper Burst Mode operation, the SYNC pin
must be grounded. When synchronized with an external
clock, the LT3971 will pulse skip at light loads. The qui-
escent current will significantly increase to 1.5mA in light
load situations when synchronized with an external clock.
Holding the SYNC pin high yields no advantages in terms
of output ripple or minimum load to full frequency, so is
not recommended.
FB Resistor Network
The output voltage is programmed with a resistor divider
between the output and the FB pin. Choose the resistor
values according to:
? V ?
? 1.19V ?
Reference designators refer to the Block Diagram. 1%
resistors are recommended to maintain output voltage
accuracy.
The total resistance of the FB resistor divider should be
selected to be as large as possible to enhance low current
performance. The resistor divider generates a small load
on the output, which should be minimized to optimize the
low supply current at light loads.
When using large FB resistors, a 10pF phase lead capacitor
should be connected from V OUT to FB.
The LT3971-3.3 and LT3971-5 contain an internal 10M FB
resistor divider as well as an internal phase lead capacitor.
Setting the Switching Frequency
The LT3971 uses a constant frequency PWM architecture
that can be programmed to switch from 200kHz to 2MHz
by using a resistor tied from the RT pin to ground. A table
showing the necessary R T value for a desired switching
frequency is in Table 1.
3971fd
11
相关PDF资料 |
PDF描述 |
|---|---|
| ACC05DRAI-S734 | CONN EDGECARD 10POS .100 R/A PCB |
| GCC22DREI-S93 | CONN EDGECARD 44POS .100 EYELET |
| LT3973IMSE-3.3#PBF | IC REG BUCK 3.3V 0.75A 10MSOP |
| RCC50DCMI-S288 | CONN EDGECARD 100POS .100 EXTEND |
| GEC49DREH-S93 | CONN EDGECARD 98POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3971IMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971IMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971IMSE-5#PBF | 功能描述:IC REG BUCK 5V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971IMSE-5#TRPBF | 功能描述:IC REG BUCK 5V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971IMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:38V, 1.2A, 2MHz Step-Down Regulator with 2.8 Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。