- 您现在的位置：买卖IC网 > PDF目录14463 > LT3971EMSE16#PBF (Linear Technology)IC REG BUCK ADJ 1.2A 16MSOP PDF资料下载
参数资料
| 型号： | LT3971EMSE16#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 1.2A 16MSOP |
| 标准包装： | 50 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.19 V ~ 30 V |
| 输入电压： | 4.3 V ~ 38 V |
| PWM 型： | 电流模式，Burst Mode? |
| 频率 - 开关： | 200kHz ~ 2MHz |
| 电流 - 输出： | 1.2A |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 包装： | 管件 |
| 供应商设备封装： | 16-MSOP，裸露焊盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LT3971/LT3971-3.3/LT3971-5
APPLICATIONS INFORMATION
Ratings of the V IN and BOOST pins, regardless of chosen
switching frequency. However, during such transients
where V IN is higher than V IN(OP-MAX) , the LT3971 will enter
pulse-skipping operation where some switching pulses are
skipped to maintain output regulation. The output voltage
ripple and inductor current ripple will be higher than in
typical operation. Do not overload when V IN is greater
than V IN(OP-MAX) .
Table 2. Inductor Vendors
VENDOR URL PART SERIES
Murata www.murata.com LQH55D
TDK www.componenttdk.com SLF7045
Toko www.toko.com D62CB
SLF10145
D63CB
D73C
D75F
TYPE
Open
Shielded
Shielded
Shielded
Shielded
Shielded
Open
Inductor Selection and Maximum Output Current
Coilcraft
www.coilcraft.com
MSS7341
MSS1038
Shielded
Shielded
V OUT + V D
f SW
Δ I L
I OUT(MAX) = I LIM –
(1 ? DC) ? (V OUT + V D )
Δ I L =
Agoodfirstchoicefortheinductorvalueis:
L =
where f SW is the switching frequency in MHz, V OUT is the
output voltage, V D is the catch diode drop (~0.5V) and L
is the inductor value in μH.
The inductor’s RMS current rating must be greater than the
maximum load current and its saturation current should be
about 30% higher. For robust operation in fault conditions
(start-up or short-circuit) and high input voltage (>30V),
the saturation current should be above 3.8A. To keep the
efficiency high, the series resistance (DCR) should be less
than 0.1Ω, and the core material should be intended for
high frequency applications. Table 2 lists several vendors
and suitable types.
The inductor value must be sufficient to supply the desired
maximum output current (I OUT(MAX) ), which is a function
of the switch current limit (I LIM ) and the ripple current.
2
The LT3971 limits its peak switch current in order to
protect itself and the system from overload faults. The
LT3971’s switch current limit (I LIM ) is at least 2.4A at low
duty cycles and decreases linearly to 1.75A at DC = 0.8.
Sumida www.sumida.com CR54 Open
CDRH74 Shielded
CDRH6D38 Shielded
CR75 Open
When the switch is off, the potential across the inductor
is the output voltage plus the catch diode drop. This gives
the peak-to-peak ripple current in the inductor:
L ? f SW
Where f SW is the switching frequency of the LT3971, DC is
the duty cycle and L is the value of the inductor. Therefore,
the maximum output current that the LT3971 will deliver
depends on the switch current limit, the inductor value,
and the input and output voltages. The inductor value may
have to be increased if the inductor ripple current does
not allow sufficient maximum output current (I OUT(MAX) )
given the switching frequency, and maximum input voltage
used in the desired application.
The optimum inductor for a given application may differ
from the one indicated by this simple design guide. A larger
value inductor provides a higher maximum load current
and reduces the output voltage ripple. If your load is lower
than the maximum load current, than you can relax the
value of the inductor and operate with higher ripple cur-
rent. This allows you to use a physically smaller inductor,
or one with a lower DCR resulting in higher efficiency. Be
aware that if the inductance differs from the simple rule
above, then the maximum load current will depend on
the input voltage. In addition, low inductance may result
in discontinuous mode operation, which further reduces
3971fd
13
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3423EMS | IC REG BOOST SYNC ADJ 1A 10MSOP |
| LT3506EDHD#PBF | IC REG BUCK ADJ 1.6A DL 16DFN |
| VE-BWD-EW-F3 | CONVERTER MOD DC/DC 85V 100W |
| LT3973EDD-5#PBF | IC REG BUCK 5V 0.75A 10DFN |
| VE-BWD-EW-F1 | CONVERTER MOD DC/DC 85V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3971EMSE-3.3#PBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3971EMSE-3.3#TRPBF | 功能描述:IC REG BUCK 3.3V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971EMSE-5#PBF | 功能描述:IC REG BUCK 5V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:250 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V 输入电压:2.05 V ~ 6 V PWM 型:电压模式 频率 - 开关:2MHz 电流 - 输出:500mA 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:6-UFDFN 包装:带卷 (TR) 供应商设备封装:6-SON（1.45x1） 产品目录页面:1032 (CN2011-ZH PDF) 其它名称:296-25628-2 |
| LT3971EMSE-5#TRPBF | 功能描述:IC REG BUCK 5V 1.2A 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:固定 输出数:1 输出电压:1.2V，1.5V，1.8V，2.5V 输入电压:2.7 V ~ 20 V PWM 型:- 频率 - 开关:- 电流 - 输出:50mA 同步整流器:是 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽）裸露焊盘 包装:带卷 (TR) 供应商设备封装:10-MSOP 裸露焊盘 |
| LT3971EMSEPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:38V, 1.2A, 2MHz Step-Down Regulator with 2.8 Quiescent Current |
发布紧急采购，3分钟左右您将得到回复。