- 您现在的位置：买卖IC网 > PDF目录5230 > LT3014ES5#TRMPBF (Linear Technology)IC REG LDO ADJ 20MA TSOT-23-5 PDF资料下载
参数资料
| 型号： | LT3014ES5#TRMPBF |
| 厂商： | Linear Technology |
| 文件页数： | 11/16页 |
| 文件大小： | 0K |
| 描述： | IC REG LDO ADJ 20MA TSOT-23-5 |
| 产品培训模块： | More Information on LDOs |
| 标准包装： | 1 |
| 稳压器拓扑结构： | 正，可调式 |
| 输出电压： | 1.22 V ~ 60 V |
| 输入电压： | 3 V ~ 80 V |
| 电压 - 压降（标准）： | 0.35V @ 20mA |
| 稳压器数量： | 1 |
| 电流 - 输出： | 20mA |
| 电流 - 限制（最小）： | 25mA |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 供应商设备封装： | TSOT-23-5 |
| 包装： | 标准包装 |
| 其它名称： | LT3014ES5#TRMPBFDKR |
LT3014
APPLICATIONS INFORMATION
Protection Features
The LT3014 incorporates several protection features which
make it ideal for use in battery-powered circuits. In ad-
dition to the normal protection features associated with
monolithic regulators, such as current limiting and thermal
limiting, the device is protected against reverse-input volt-
ages, and reverse voltages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal operation,
the junction temperature should not exceed 125°C.
The input of the device will withstand reverse voltages
of 80V. Current ?ow into the device will be limited to less
than 6mA (typically less than 100μA) and no negative
voltage will appear at the output. The device will protect
both itself and the load. This provides protection against
batteries which can be plugged in backward.
The ADJ pin can be pulled above or below ground by as
much as 7V without damaging the device. If the input is
left open circuit or grounded, the ADJ pin will act like an
open circuit when pulled below ground, and like a large
resistor (typically 100k) in series with a diode when pulled
above ground. If the input is powered by a voltage source,
pulling the ADJ pin below the reference voltage will cause
the device to current limit. This will cause the output to go
to an unregulated high voltage. Pulling the ADJ pin above
the reference voltage will turn off all output current.
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp volt-
age if the output is pulled high, the ADJ pin input current
must be limited to less than 5mA. For example, a resistor
divider is used to provide a regulated 1.5V output from the
1.22V reference when the output is forced to 60V. The top
resistor of the resistor divider must be chosen to limit the
current into the ADJ pin to less than 5mA when the ADJ
pin is at 7V. The 53V difference between the OUT and ADJ
pins divided by the 5mA maximum current into the ADJ
pin yields a minimum top resistor value of 10.6k.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled
to ground, pulled to some intermediate voltage, or is left
open circuit. Current ?ow back into the output will follow
the curve shown in Figure 4. The rise in reverse output
current above 7V occurs from the breakdown of the 7V
clamp on the ADJ pin. With a resistor divider on the
regulator output, this current will be reduced depending
on the size of the resistor divider.
When the IN pin of the LT3014 is forced below the OUT
pin or the OUT pin is pulled above the IN pin, input cur-
rent will typically drop to less than 2μA. This can happen
if the input of the LT3014 is connected to a discharged
(low voltage) battery and the output is held up by either
a backup battery or a second regulator circuit. The state
of the SHDN pin will have no effect on the reverse output
current when the output is pulled above the input.
50
V OUT = V ADJ
T J = 25 C
45 V IN = 0V
40
35
30
25
ADJ PIN
ESD CLAMP
20
15
10
5
CURRENT FLOWS
INTO OUTPUT PIN
0
0
1
2
3
4
5
6
7
8
9
10
OUTPUT VOLTAGE (V)
3014 F04
Figure 4. Reverse Output Current
3014fd
11
相关PDF资料 |
PDF描述 |
|---|---|
| 25MXC22000MEFCSN25X50 | CAP ALUM 22000UF 25V 20% SNAP-IN |
| 100MXC1800MEFCSN30X30 | CAP ALUM 1800UF 100V 20% SNAP-IN |
| 200SXC680MEFCSN30X30 | CAP ALUM 680UF 200V 20% SNAP-IN |
| LT3082IST#PBF | IC REG LDO ADJ .2A SOT223-3 |
| MIC5353-1.8YMT TR | IC REG LDO 1.8V .5A 6TMLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LT3014HV | 制造商:LINER 制造商全称:Linear Technology 功能描述:250mA, 4V to 80V Low Dropout Micropower Linear Regulator with PWRGD |
| LT3014HVEDD | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA, 3V to 80V Low Dropout Micropower Linear Regulator |
| LT3014HVEDD#PBF | 功能描述:IC REG LDO ADJ 20MA 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:MIC5365/66 Ultra-small LDO Regulators 标准包装:1 系列:- 稳压器拓扑结构:正，固定式 输出电压:3V 输入电压:最高 5.5V 电压 - 压降（标准）:0.155V @ 150mA 稳压器数量:1 电流 - 输出:150mA 电流 - 限制（最小）:200mA 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:4-UDFN 裸露焊盘，4-TMLF? 供应商设备封装:4-TMLF?（1x1） 包装:Digi-Reel® 其它名称:576-3192-6 |
| LT3014HVEDD#TRPBF | 功能描述:IC REG LDO ADJ 20MA 8-DFN RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 系列:- 产品培训模块:More Information on LDOs 标准包装:50 系列:- 稳压器拓扑结构:正，固定式 输出电压:3.3V 输入电压:最高 15V 电压 - 压降（标准）:1.1V @ 800mA 稳压器数量:1 电流 - 输出:800mA 电流 - 限制（最小）:800mA 工作温度:0°C ~ 125°C 安装类型:表面贴装 封装/外壳:TO-263-4，D²Pak（3 引线+接片），TO-263AA 供应商设备封装:D2PAK-3 包装:管件 |
| LT3014HVES5 | 制造商:LINER 制造商全称:Linear Technology 功能描述:20mA, 3V to 80V Low Dropout Micropower Linear Regulator |
发布紧急采购，3分钟左右您将得到回复。